Scott,
Thanks you very much for the hard work with keeping all of this going and up to date with guidance along with answering many questions.

73’s
Joe
WD5Y

Vin,
This is really good to hear. It sounds like Apache Labs is addressing their customer service and contact issues. They have a really great product line and service with communication before, during, and after the sale really matters utmost.

Thanks,
Joe
WD5Y

Glad it helped. I have to be reminded quite often to save the transmit profile for the same reason when making changes, etc.

73’s
Joe
WD5Y

After you check the vac box the go to the transmit tab and do a profile save and I believe the next time you start it should come up checked.

73’s
Joe
WD5Y

Thanks for the information. Great option.

73’s
Joe
WD5Y

I know this is different from the usb - relay setup but another option is using the OC outputs with a bcd board. I use one supplied by W6PQL, works very well with the Anan. Hope you get it worked out. I added the photo of the board (lower left side), in my amp.

73’s
Joe
WD5Y

Hello Ritchie and Ernst,
This is really appreciated! The opportunities and capabilities of this are very numerous. This will allow cross communications between apps with Thetis. I'm still trying to wrap my head around this with my present setup, I have a wavenode wn-2 interfaced to a LDMOS amp that ...

Just wanted to say Thank You to all that made this happen. You gotta hear this, it is great! I used the adjusted settings mentioned above for a start.

Thanks and 73’s
Joe
WD5Y

Please, just as a point of clarity, would someone post the correct “setpk” values for the different Anan models? I take it, that there is a table in the code for the proper selection.

Thanks,
Joe
WD5Y

I just wanted to mention, the Noctua fans that Abhi used in this design are very quiet. I modified the circuitry in my meanwell power supply to install these and all of the difference for quietness in use, very pleased with noise abatement. For all who have this unit on order, this sure looks great ...

Great, glad you got it going. I know it can be frustrating but when one thing fails you back up and try something else. Also, you posting results hopefully helps someone else.

73’s
Joe
WD5Y

Not sure if you tried this yet but re-name the .rbf file to Metis.rbf. If you have done this already, I apologize for repeating. I had the hang up on the "erasing" step; I kept stopping and starting and finally it went to the next step of "programming", very slow too. It had actually erased the ...

One thing you might try is try to connect without the Ethernet cable plugged in and see if the same error comes up? You may try completely removing the bootloader software and reinstalling with admin rights and check properties on the software after downloading, I make sure I check the “unblock ...

I believe Scott is correct in getting you into the network adapter area, you do not seem to be connecting at all with the bootloader. My failure along with a few others was after actually connecting, I could see a connection indication; even change ip information. For me it was locking up during the ...

Thanks, I’m going to uninstall what I have now and start from scratch with your link. I will only install the bootloader.

Thanks,
Joe

I wasn’t sure if the adapter settings had any effect on the bootloader, it was coming up with the correct MAC address. I am connected straight from the pc to the radio, no switch involved. I was hoping that the static ip address was ok as the bootloader was connecting fine. Now I know to leave the ...

I am running win 11 pro, the last time I used the bootloader to upgrade I was using win 10. I did finally get the latest protocol 2 @ version 2.2 loaded after approximately 4 hours of back and forth working with different scenarios to load it. I have an 8000dle. The bootloader finds and recognized ...

I’m sorry for replying so late. The schematic is at the bottom of the posting, hopefully that helps but honestly as Scott mentioned the fixed resistors would be an easier route. I would fuse the circuit just for added protection. I had to go back into that small db9 connector later for another ...

You can’t directly supply a bcd “high” output, but I did make a small interface that fit in a db9 enclosure that I use for my amplifier band “bcd” interface. It works very well. You may have another approach, hope this helps. Please check out this posting here from some time back.

https://community ...

Thanks so very much Ritchie, you are continuously updating and refining Thetis.

Thanks and 73’s
Joe
WD5Y

Thanks so much Richie,
I looked over all of your cleanup of so much of the massive lines of code! All I can say is you must be super fast at working lines of code. I couldn’t believe all of the work you did and with all of the great additions. Thanks again to all for the great updates and additions ...

Thanks Bryan,
I really appreciate your help and work on this. I had the blockmode set up and made a contact on 75 earlier and had great reports. I will work with different settings when possible, could you give me some suggestions on values to try ? I am running a 14900k cpu, just stock settings ...

I just wanted to mention how much this feature is appreciated. I had a bit of trouble getting the Driver name recognized or so I thought. I am running an Apollo Solo Thunderbolt and the driver was not recognized when I searched using the "hostsample" app. I figured well just enter what is listed in ...

Ritchie,
Thanks very much, all of this is awesome!! Also, thanks to all of the others mention regarding the asio work. There are so many contributors that are also working in the background here and it is so appreciated !

73’s
Joe
WD5Y

I have been working a bit with the collapsed view code, the pa profile tag had to be re-located for that view. I placed it at the lower screen view in collapsed. I have not uploaded anything yet to my repo. I worked on a few other items in the collapsed view that may be of interest to Richie but he ...

Thanks Richie,
There are many additions and improvements in there. You put a lot of time in this for sure. Very much appreciated!

Take care and 73’s,
Joe
WD5Y

I believe it would be opposite direction of the filter screen, but I could be wrong.

Joe
WD5Y

Thanks Sigi, have a great day! Also, thanks to everyone for contributing.

Joe
WD5Y

Something just became clear on this error from the earlier versions, this debug error came up at Thetis exit which makes sense this is when the tx - save on EXIT doesn’t happen, possibly a complete proper exit didn’t take place.

73’s
Joe
WD5Y

Hello Ritchie,
I downloaded your latest last night. I wanted to mention that the earlier versions failed as mentioned here but your latest works without this glitch. Honestly I thought you had purposely fixed the problem but was just waiting to post it. The way I confirmed is, I run the debug (64 ...