Also, the TX bandwidth error does not occur if sample rate is 192000 Thanks Jeff Good day, Wondering if anyone found fix for TX bandwidth error in dup mode? The visual in the display looks to be double the bandwidth I am actually running. This occurs only when pure signal is on. I am running: ANAN ...

I'm pretty sure I've read something about this behavior in the forum before. But I can't find the post. I suspect that it is a Thetis problem. I would like to almost rule out the firmware. Since Thetis v2.9.0.5 is not an official version, it may suffer from bugs. You might try the TAPR release &quo...

Hi Rick, hope all is well, I tried to send a PM but it is stuck in outbox !! I am running: ANAN 100, Thetis v2.9.0.5 x64 (4/21/22), Firmware: Protocol 2v 10.8.0 pre20 Not a huge deal but hoping its an easy fix: The TX bandwidth visual (with DUP on) in the display looks to be double the bandwidth I a...

Also, the TX bandwidth error does not occur if sample rate is 192000 Thanks Jeff Good day, Wondering if anyone found fix for TX bandwidth error in dup mode? The visual in the display looks to be double the bandwidth I am actually running. This occurs only when pure signal is on. I am running: ANAN 1...

Good day, Wondering if anyone found fix for TX bandwidth error in dup mode? The visual in the display looks to be double the bandwidth I am actually running. This occurs only when pure signal is on. I am running: ANAN 100, V2.8.11~2/V10.8.0, 21k8, Firmware: 2 10.8 pre20 http://n8rws.com/PSOff.JPG ht...

Hi Rick, just tested with Thetis 2.8.11g on x64. Looks very promising, PS runs excellent on all bands, receivers working independend on all samplerates. Just 3 little quirks: 1) Panadapter is offset by CW Pitch during Tune. This was the same in older versions, at least since pre20. 2) MON only work...

Gray face ANAN100, Pre20 v2.7.0 (a3) All working very well here, PS very stable... have not tested / do not use different sample rates between RX1 & 2. Only issue I found is when I "TUN" or hit the tune button the display shows a slight frequency offset from the set operating frequency...

Thanks many times over !!! Working top shape here too: cold and warm.... ANAN100 Gray, Pre20, 2.7.0 (a3)

Jeff
N8RWS

Yea !! PS works very well when rig is warmed up... but woooa... big IMD and distortion when cold.

ANAN100 Gray face

2.7.0 3/1/2020 (a3)
Pre18

Thanks

Jeff
N8RWS

Hi,

Many thanks for the work on this.

Just tried pre14 with my ANAN 100 using crosstalk for PS

PS will lock in and correct but as I am transmitting it will stop correcting, then start up again. Feedback is blinking the entire time. Also receiving SEQ errors !

Thanks

Jeff

Thanks for all the work !! I am running Thetis v2.6.9 ANAN 100 With 10.8 pre6 PS will lock in and stay locked for several seconds then the "feedback" will stop and soon after that "correction" will stop. After I unkey and re key the cycle repeats. With 10.8 pre7 PS locks in but t...

Whoops... I did not have the keyboard shortcuts enabled... sorry

73

Jeff

Thanks so much for your hard work on this !! I am running ANAN 100, just installed 10.8 pre5. The keyboard space bar control of the toggled function (PTT/MOX, VOX etc) is not working. Is this to be expected with this version of firmware?

Running Thetis v2.6.9 (1/24/20)

Thanks,

Jeff
N8RWS