Scott,

I've changed the Jumper and all appears to be well.

I'm assuming that no Bias was causing an inpedance mismatch and causing the noise on the mic.

Thanks again.

Glenn M1AQO

Scott,

Correct on all points.

It will be interesting to see the result when the Bias is connected.

It would appear in my current setup that there is an impedance mismatch due to no Bias powering the FET in the element.

It also explains why there is only two shorting clips in the radio, because ...

Hi,

I'm just looking for some help with the Anan 10 front mic input.

I'm using a PC Electret mic wired:

Ground: Sleeve
Mic: Tip & Ring

The mic is working fine with the radio, apart from*

Ive checked the jumpers in the radio:

Jumper 4 (Mic) is connected to terminals 2 & 3 for "tip" mic input ...

Hi,

I just wanted to ask for confirmation of the pins for Amp Keying on the Hermes board Anan 10 (26 Pin I/O)

Looking at the schematic it shows pin 1 for PTT out and pin 2 for ground.

When converting to an IDC connector according to the Anan 200 manual this flips to pin 26 and 25 respectively ...

Strange.

Why announce something then remove the link

You would have thought they would have updated us
with the status.

Oh well.

Hi,

Is there any update on delivery times. I also believe that the PA is 500w from what I’ve heard.

Is anybody aware of this ?

That would maybe explain the higher voltage supply required.

Thanks

Glenn

Thanks Scott

Hi,

I would like to try Thetis therfore need to download Protocol 2 FW for the Anan 10.

Can somebody provide the link for the version I should be using please.

Also what is the latest version of Protocol 1 ?

This radio has been purchased second hand and I would like to download both the latest ...

Perfect Walter, Thanks !!

Using Power SDR MRX v3.49

1, Is there an option to display the SWR in the display window on Tune. It displays the SWR when in SSB and transmitting, but I want to use the SWR meter to tune my Doublet whilst using the tune option.

2, Is there also a way to remove the centre line displayed on the ...

Hi,

Looking for an Anan10e.

A boxed, clean, unmodified Radio required.

Thanks

Glenn M1AQO

Not forgetting this is the I7 version, if there is a difference.

Does anybody know how much voltage is applied for
the microphone when the Bias is selected?

Thanks

Glenn M1 AQO

Hi,

New to Anan.

Is there a new version of the PowerSDRmrx user
notes ? I’m using 3.49.

I can only find a download with updates from 2012 / 13.

Thanks

Glenn
M1AQO

To save rambling through the post, Anan 7000dle MKII
users using mic in (front or rear on radio).

If you TX and don’t speak do you hear noise through
the monitor and see it on the panadapter ?

I am experiencing this noise with and without the
mic plugged in with the mic level set.

Thanks ...

Hi Scott,

Thank you for the quick response.

If I reduce the Mic gain slider to -10db (minimum setting) the noise disappears on the panadapter with a mic gain reference on the meter of -80db. This is with no mic plugged in.

If I do the same procedure with mic plugged in the noise does reduce but ...

Hi Scott,

I've looked at the information but can't figure out the audio path for the USB / Headset routes in relation to the codec.

I've taken your suggestion and set up a USB Headset and the noise isn't present when the microphone is keyed, so clearly there is
a problem with the front and rear ...

Thanks Scott !

Hi Scott, Thanks.

I will pick up a USB head set and give it a go.

Once question,

Does the line in or USB connection not enter the CODEC via these routes ?

I thought the digital process started here after the microphone.

Thanks

Glenn

Thanks

Hi,

Thanks for the advice.

I don’t have a USB headset but I do have a USB
microphone, so I assume I can use VAC2 to test because VAC1is being used for the receive audio.

My 7000 had the built in I7 processor so
I assume I will use the USB on the back of the radio?

Thanks

Glenn

I’ve done further testing and the noise isn’t
present on TX.

When I turn the mic gain down irrespective if
there is a mic plugged in or not, the noise disappears.

The noise is present through the monitor function and is shown on the panadapter when TX keyed and mic gain is turned up, with or ...

It terminates to a trs plug.

Thanks

Glenn

Hi,

I’m a new user of a 7000dle MKii.

I’m trying to set up the TX audio using the rear mic
input with a standard PC Condenser Mic.

I have set the Mic to tip, Bias to on and PTT to off utilising the space bar to key up.

With the monitor on mic unplugged and the PTT keyed without speaking there ...

Thanks

Hi
Can anybody tell me if the Anan10e is
capable of Diversity Receive.
Regards
Glenn M1AQO