Radio has been sold.

FS a very clean one owner Anan 7000DLE MKII with no issues. Has latest 2.2.2b firmware, Protocol 2. I've been running the latest v2.10.3.8 software for a few weeks. Purchased from HRO March 2020.
I prefer local pickup (Atlanta GA) or will meet someone within a reasonable distance from Atlanta or ...

Un-check 'MON' next to TUN. I know when I have MONitor on I hear a tone also.

Dave
k4em

Problem solved.
Thanks for the info Scott, the issue was in Thetis. I stared to poke around the Network/TCI screen and Enabled 'CWL/CWU becomes CW (out). CW is now showing up in Log4om when going into CW mode on Thetis.

Thanks for your help, it got me think about how the data was transferred to ...

I was working the 'WWA' event this past week and I noticed my logging S/W was not changing to CW mode. It would change to USB, LSB, AM, FM, FT8 and FT4 but not CW.
I've recently started using CMaudio with a Behringer UMC202HD and ASIO driver. I also know that I no longer have cw sidetone. Could this ...

Thanks Scott,

For the explanation, guess I'll just use my 7300 for cw. I only chase dxpeditions for cw contacts anyway. Arthritis is too bad to use a key anymore.

Dave
k4em

No side tone in CW using CWX & 'SEMI' after Thetis and cmASIO upgrade. I do have sidetone if CW is set to QSK and also pressing TUN but not in SEMI mode.

I upgraded to final release 2.10.3.5 and tested SSB & digital modes, all ok. I'm using a Behringer UMC202-HD. I then configured cmASIO per ...

These work very well for supplying phantom power to a mic. There are other brands available as well.
https://www.amazon.com/Nady-SMPS-1X-1-C ... B000XUUXB8

Dave
k4em

I've noticed the new PC cases, parts, etc all seem to have LED lighting. Has anyone noticed any birdies or other issues using the LED lighting? I'm building a new PC and the case has fans with LED's, not sure if I should go with the LEDs connected. The dimms, and cpu fan do not have LEDs just the 3 ...

TCI is now working with RFKit amp & Thetis.

The Best just got Better.

Thanks Ritchie,
Dave
k4em

I switched off the amp and the Client count dropped to ZERO, took almost 2 min.

When I had EESDR3 up, TCI enabled, LOG enable. I tried several scenarios to get some info to show up in the log, it remained empty.

Dave
k4em

Ernst,

Also, toggling 'enable' causing the amp to revert to UNIV and the message 'no TCI available' displays. Toggling 'enable' it goes back to TCI. All looks OK to me.

Dave
k4em

Ernst,

I downloaded the EESDR s/w and setup per your instructions and it worked. My RF2K-S amp is now showing TCI, nothing showed up in log.

Dave
k4em

I have both Thetis & RF2K-S amp set to my PC ip and port is 50001. It is configured like Ernest's example picture's.

When cycling thru the CAT setup screen I never get TCI to appear in upper right hand corner of amp as shown in Ernest's amp front panel picture. The message is always 'no TCI ...

I guess I should have said that UNIV seems to be the default selection. TCI is always shown as 'No TCI available' on amp front panel. I thought the log data was promising as it did shows commands being sent from Thetis.
But, when I change the status in the AMP to TCI, Thetis reacted to this by ...

Ramdor,

Yes I was using 127.0.0.1, I changed it to my PC ip address. Still did not work. I did not start my logging program or JTDX, both off while testing.
I started in Admin mode, clicked on 'Firewall' setting. I rebooted just to make sure all started fresh, did not work.

In the rfkit amp there ...

On your RF2K amplifier is the common DC terminal tied to the chassis?

I have no idea, maybe they would know on the RFKit forum.

Dave
k4em

This is just an FYI post, I'm not complaining just passing along some info.

Just installed 2.9.0.3 and all seems to be fine. I configured TCI with Log4OM & JTDX, the CAT I/F is working. I turned on TCI logging and both Log4om & JTDX are sending/receiving commands.
The problem is my RF2K-S amp is ...

I'm using JTDX ver 2.2.159; Thetis ver. 21k9. I'm using audio VAC, I understand that TCI audio is not implemented in Thetis yet.
JTDX & Thetis runs fine in regular mode just not F/H mode when TCI is configured.

Thanks for the info.
Dave
k4em

Edit: Sorry, I switched back to Virtual serial port cat ...

I implemented TCI in Thetis (21k9) and successfully setup Log4OM & JTDX and have been running fine for 2 weeks. Yesterday I tried F/H mode for the first time and it did not work. I switched back to VAC and it worked fine in F/H mode.
Setup with TCI; in F/H it goes into transmit for about 1 sec and ...

Does the TCI implemented in Thetis have PTT control. I know it has CAT but is there PTT control too.

Dave
k4em

I'd like to see the full TCI implemented into Thetis; Audio & CAT. I use a RF2K-S amp which has TCI client, Log4OM & JTDX all have TCI capability. I am waiting for TCI in Thetis. I'm not really interested in trying the experimental version's being used right now. I'll patiently wait for the approved ...

This brings a question to mind. What are all the defaults supposed to be after an install. On my install both were off.

Dave
k4em

Scot,

My bad, when you announced 'UPDATE FW 2.8.18 14 AUG 2021' and further down it said, Thetis build 2.8.11 21f will show the full firmware version number , etc.
I thought the new FW included 21f. Which means I misunderstood.
I suppose i'll be ok to leave it as is, the rig seems to be running ...

Scott,
No I did not install 21f, just the 2.1.18 FW which went smoothly.

Dave
k4em

OK, I updated the FW to 2.1.18 on my 7K DLE MKII, Setup/General/HW now shows ver 2.1. I see no new buttons or changes. I also changed my Skin & buttons to Clarity N from W1AEX site. Does FW 2.1.18 include the 21f changes? Is there a Change Notice document that lists all the changes to 2.1.18?

Dave ...

I powered off the SDR 2 weeks ago and I used my IC7300 for a couple of weeks. I powered the 7K DLE MKII back on and started up FT8. I immediately noticed the birdies (marked in RED) on my signal. The Green dot is my normal looking signal. I have never had these before on FT8 using PowerSDR, Thetis ...

Rob,
I'm using the K2GX 'World Time' skin. I installed this in late March about 2 weeks after I received the radio and installed Thetis. I don't recall installing any separate buttons or sliders.
I just noticed in your example on your page, the K2GX 'World Time' skin says 'PowerSDR' at the top, is ...

Hi Scott,

7K DLE MKII, firmware latest I could find 2.0b & 2.8.11 64 bit Thetis.

Dave

Can someone provide some screen shots of a transmitted cw signal or video? I have my 7K DLE mkII setup for semi-CW, I just want to see what a clean signal should look like.

Also, some cw settings examples, how do you have your rig set? I followed the ver 1.1 manual and all seems to work.

Also ...