I opened a BUG on this and received a reply from Richie. Apparently this behavior is functioning as designed. The Antenna Selector in the GUI only works when within the Ham Bands. -Rick Yes the implementation is to only work with ham bands. // set RX antenna to new antenna 1-3 // this must also canc...

I connected a second antenna to Ant 2. I can switch between Rx Ant 1 and Rx Ant 2 using the Thetis selector at the bottom of the UI. I can also configure the antennas by band in Setup, Ant/Filters tab. However, UI selector only works when the VFO is in the Ham Bands. When I go out of the Ham Bands t...

Hi Richie, I am running Thetis v2.10.3.5 Pre-Release 3. I have it configured to prevent Tx on non-Ham freqs in the US. (Extended not checked in Setup). It works as expected with one minor thing. If I Tx with the Thetis MOX button or the spacebar, I get the pop warning window, I close the window and ...

Thank You to Richie, Ernst and everyone who contributed to this release. This is a truly amazing work. Your efforts are appreciated so much.

73, RIck, W1RHS

7000DLE MKII Orion MKII Ver. 2.1.18 P2 v3.9

Hi Richie, I don't know if this is important but I thought I would log it here just in case. I get three application errors in the Event Log when I launch Thetis: The Open procedure for service "WmiApRpl" in DLL "C:\WINDOWS\system32\wbem\wmiaprpl.dll" failed with error code The d...

Hi Richie,

Running Version 21K9(rc5b). No instances of 0x8899000C in my error log file. THANK YOU for all your fine work.

73

Rick, W1RHS

Hi Richie, I am not sure how this is supposed to work, but if I un-check Alex in the Setup => General Tab, then re-checking it does not re-enable it. I have to close and re-open Thetis in order to turn it back on. I am using a 7000, P2, and 21k9(rc1) Thanks for all your amazing work! It is appreciat...

Hi Richie,
I have been keeping up with your updates. I'm really enjoying the enhancements. Your work is truly appreciated.

Hi Paul, Here's what I saw in there. J27 is the black 3.5mm TRS jack facing outward at the edge of the board along with the SMA connectors. J9 and J8 are black plastic connectors. Starting with J27 at the board edge and working toward the center of the board the order is J27, J9, J8. On mine I moved...

Hi Paul, A few posts backward from here Scott mentions that Left and Right are reversed. I'm not perfectly clear on this but I think this is what happened. J9 (plastic jack) on the Orion Board is supposed to be the Left Speaker. In parallel with J9 on the board is J27 which is a TRS 3.5mm "ster...

Hi Guys, I decided to try the rear L R speaker jacks on my 7000DLE MKII. Both jacks had only L audio (Rx1) but, of course, the headphone jack had both L and R and Rx1 and Rx2 could be sent to either or both by panning. I opened up my ANAN and swapped the plug on the Orion board from J8 to J9 and tha...

2.8.11 x64 runs great on my 7000DLE MKII Protocol 2. I realize the Midi support was not changed. Just confirming that it works with my Behringer CMD PL-1 Midi controller. Thanks to everyone who helped make this possible!

Thank you for 2.8.8. Installed perfectly!

I upgraded from 2.8.6 to 2.8.7. In both versions of 2.8.7 the Rx and Tx antenna selection controls in the status bar are no longer there. What am I missing? I had them with 2.6 but with 2.7 they went missing. Scott WU2O responded that they were temporarily removed for safety until the bug was fixed...

Well, I have to say this work is truly amazing and appreciated. 2.8.7 is working nicely here. System load is less with the x64 version. Many thanks to the developers working on this.

I upgraded from 2.8.6 to 2.8.7. In both versions of 2.8.7 the Rx and Tx antenna selection controls in the status bar are no longer there. What am I missing?

Thanks for Thetis_270_210820_1735_a3 Richie. Working well here.

My new (black) 7000DLE MK-II (no internal PC) arrived from AU two weeks ago at the end of February. I can freely flash between Protocol 1 / PowerSDR and Protocol 2 / Thetis and SDR Console. I am not experiencing any problems.