NC3Z wrote:Wouldn't it be cool if you had a tool to just type in a word and it pops up the related settings?

Screenshot 2023-12-24 095558.jpg

thanks for that too!

w-u-2-o wrote:Setup > General > Options > Options-1 > Miscellaneous > Reverse Wheel

Thank you!

I'm not sure which version this is since, but when engaging Pure Signal I used to see the unwanted sideband emission disappear on the waterfall during tx, showing how well it is working.

Now both sidebands look the same. Pure Signal bar is green on tx.

(2.10.3.4)

Thanks

Andy
EA5JGN

Sorry if I've missed this, but is it possible to change the mouse wheel direction? i.e. if I scroll down, the freq goes up!

Thanks!

(2.10.3.4)

EA5JGN

Got it thanks!

No doubt I'll be back...

Ah thanks didn’t notice the port.

The screenshots someone posted above say to use Flex…

Also, how can I enable a 2nd radio in N1MM.

Thanks

EA5JGN.

Still no joy with this. Here are the relevant screens: I don't know what that error popup is referring to.

Any help please?

Thanks

Andy EI5JGN

I didn't notice that one when I searched, so thank you.

Can someone please help me set up Thetis and N1MM to talk to each other?

I want to run them on the same PC.

Thanks

Andy EA5JGN

@ w-u-2-o thanks, will do!

Thanks - just what I wanted. But I'm unclear on the version of Thetis, my ver is 2.8.11 - are you saying I need an earlier version?

Mine doesn't have the IP settings on the CAT+ tab.

thanks

A

Is there a step-by-step guide to interfacing to N1MM please?

It would be nice if they'd talk by TCP too.

thanks

Andy

That does it, thanks.

Interestingly, the receive audio quality is better on some SDRs when there's some carrier, around 10dB down.

Which is what I was wondering!

A

Hi, I'm wondering if its possible with the Anan to tx SSB with carrier - i.e. not completely suppressed, or reinserted...

I'd like too do some experiments with the carrier around 10-15dB down.

Just a thought...

A

Installed on my 7000DLE yesterday with no issues. Looks good and works just fine!

How would I know? Thats where I'm hearing it from.

No processing on that, just +10dB. And that's with no audio cable connected to inputs.

That is with the audio input to the tx disconnected, audio taken from the headphone output, Apache MOX on.

Mixer is grounded like everything else, all interconnecting cables are balanced, with an isolation transformer on the audio input. But like I say, that's with no mic or audio input connected.

A

It is also connected to the house ground.

And since I'm in Ireland I'm not bound by US electrical code.

And as I said, I don't believe its RF feedback, as it's irrelevant to the OP power. In the recording above, the Apache is on SSB, there is no audio being fed to it, therefor its not actually ...

Each piece of equipment is grounded by a separate cable to a central point, which is then connected to a couple of ground rods.

But this does not sound like a ground loop. It sounds like a digital hash with a slight high frequency hum, not 50Hz (which we use here).

Here's a recording - this has ...

This is a strange one, I find with my Anan 7000DLE, on transmit the headphone connection, supposedly muted, outputs some noise.

This is a kind of digital-sounding hiss/hum, which to the uninitiated sounds like a fan running in the background.

Its a problem for me because of the way I route the ...

Final question (can't promise...) how do I know if the Bypass input is getting an acceptable signal level?

Thanks

EI2HH

Great! Thanks for the info.

EI2HH

Thanks for the useful reply Rob. How does one tell the Annan 7000 to listen to the 'bypass' input? Mine has a bnc marked bypass, no loopthrough connector which I think the older boards had.

A

If I was to take a sample AFTER my external linear amp and run that to the sample input, would Pure Signal then be able to correct any non-linearity in the transmitter signal caused by the linear amp?

What level of signal is OK to feed in? i.e. what level level should I set my extractor to ...

Ah thanks for the explanation. I thought the explanation above was for older units- I see now it does apply.

Andy

Oh I assumed it'd already be Protocol 2.

Is there a guide to doing this on here?

My 7000DLEMkII is brand new, running Open HPSDR right now.

Do I need to update the firmware to run Thetis? Is there any way of telling?

thanks

Andy EI2HH

Hi, newbie here using OpenHPSDR and a 7000.

Is there any way of seeing an oscilloscope-type display of the received (and/or transmitted) RF waveform?

i.e. the RF envelope before demodulating.

Useful to check modulation depth etc. At the moment I use an external scope to monitor and set up my ...