If you mean the signal connected to ADC 2, I've had a similar issue. Seems the previous owner had input a high level signal into RX2 (ADC 2). It fried the filter labeled RLP-40 and the back to back diodes labeled D22 (part number GBLCo3C) . I was still receiving but signals were at least 6dB down ...

Thanks for posting. Perhaps setting ip address to static (vs reuse previous address which is how I had it set in Thetis) will eliminate the somewhat random loss of synch issue I had been having. this with a W10 computer directly connected to the 7000dle with a dedicated 2 port 1G ethernet card ...

Thanks for listing the link but link has a typo. Should be: https://www.lw-sdc.com/

Also, get an error when trying to download the manual (error says not found or something like that).

Looks like an interesting collection of capabilities.

Ron
N4XD

Attenuation during transmit setting seems to randomly reset itself to zero. I noticed this during split operation on 20 ssb. I believe having the attenuation at max during transmission helps protect the 2nd receiver so would be great to set it and have the setting stick

Ron
N4XD

Problem resolved. I have a speaker attached and its normally off when I operate cw. I turned it on then back off and the cw side tone issue was resolved. NO idea what interaction happened.

RE: cw sidetone

Yesterday I installed rc3. All seems fine except, the cw sidetone, which I used to control with the master AF control, is much, much too quiet even with the control maxed out at 100. Anyone else having this issue and, if so, what was fix?

I do use an external winkeyer.

Thanks

Ron ...

In reading this and other posts I'n not sure the question of whether there are still relays in the T/R path has been answered. Since I've not seen any announcement that the G2 has made the switch to pin diodes I'm assuming, until someone corrects me, that the G2 still uses relays AND that the pure ...

Richie thanks for all the updates!!

Ron
N4XD

I'm that "other" fellow.

In the manual, which admittedly is quite a bit out of date, it said set CW delays (both key up and key down) to at least 30ms otherwise will get unusual results. Indeed I found, with other versions of Thetis, this to be the case. That and the long delay needed for all the ...

Scott, thanks!

That's exactly what the issue was.

I ran Thetis as admin and did the check firewall. It came back as OK.

Next I opened my anti virus program, AVG free. It had somehow switched to "don't trust this network". Changed and indeed radio back up and working.

I really appreciate your ...

I'd prefer not to. Thetis works fine on a laptop running W10.

Some more testing reveals the transmit side of Thetis and the radio works fine. Its just the receive side. Completely blank display. No noise, nothing. Checked ADC settings are they show standard set up for P2. Antenna set up all good. I ...

Operating system: W10
Recently did some updates to my Asus desktop. Running i7-11700. Updates included Bios and other items.

After update Thetis starts, sees the Anan 7000dle but, absolutely no rf from radio. Tried radio with another computer and no issues.

Did try the database reset but that ...

I checked and didn't see such an assignment available. It sure would be nice to program a MIDI button to swap between rx and tx antenna under the Thetis VFO A and B section of Thetis.

I'm not at all well enough versed in Visual Studio to try to create such a function. Any takers? Or even hints on ...

Found issue. User error. I had moved the radio and, somehow, flipped the switch on the bottom to boot loader. Moved it back and all is good. Sorry for the bandwidth

Ron

Was working perfectly. In fact just ran the whole CQ160 WW with no issues. Went to restart and Thetis shows error box when trying to power on saying "Error starting SDR hardware"

On the lan connection the left light is on but the right blinks for a while when the cable is first connected then stops ...

Yes, sorry. Not fully awake yet. Will download and install latest version.

Sorry for cluttering this stream up

Ron

Unusual behavior with diversity. Running thetis 2.10.3.3 on W10 64 bit and a 7000dle. Turn diversity on then off and rx1 goes full screen noise. Tried cycling Thetis off then on and it hung up. Had to go to task manager to shut it down.


Ron
N4XD

Mark when I received my (used) 7000dle I suspected rx2 wasn't hearing as well as RX1. I was right. I found the filter immediately in line with the input was very lossy. Removed (that was a chore as it has contacts on all sides!) and replaced but still seemed a little numb. Went back in and looked ...

Good advise. I checked and indeed, when transmitting rx2 is shorted to ground. With, of course, the "ground bpf" box checked in Thetis The signal I see on thetis must be internal leakage or something like that. Not a signal present on rx2.

Ron
N4XD

Rafael, that's the question. Is the band pass filter really grounded? Can anyone on the forum verify that it is?

Ron
N4XD

Re "ground bpf2 on xmit

I have that checked but, when I transmit I still see a very strong signal on RX2 tuned, o course, to same as transmit frequency. I have always wondered if the rx2 band pass filter was actually grounded.

Ron
N4XD

Thanks Paul.

From reading the other string, seems no changes have been made. That is a REAL shame since, to me, the use of relays is a downside for the radio. Perhaps I'm doing something wrong but I found that, when using the internal keyer, a VERY long delay (hundreds of ms) was needed to ...

Are relays still used for T/R switching or does the G2 use pin diodes? If relays, any differences from the 7000 series? Specifically, is the pure signal relay still in parallel with the T/R relay so its always used even if the mode isn't SSB?

Thanks
Ron
N4XD

Version 2.0.0
Protocol 2 (v3.8)

Ron

Scott

Failed to answer the first question you had. Yes, it works fine with the other laptop which is also running W10.

Turned firewall off, changed lan cable and same result as above. Baffling.


Ron

Scott, thanks. I do not have the W firewall on. I did the firewall check and Thetis came back saying all OK. I'll try disabling my other firewall. But my other computers work fine with it enabled (I use free versions of AVG and Zone Alarm).

Appreciate the reply!

Ron

New laptop is I7 6820 cpu and 16Gb ram
Radio: Anan 7000dle

Issue:
Connects and sees Thetis
Does not receive anything.
I can press "tune" and indeed the radio sends carrier.

I've verified correct antennas selected but absolutely nothing. S meter shows something like -398 for signal level ...

Mike, thanks for that info.

Richie thanks for incorporating the choice in your next update. To me, seems that there is no harm in keeping the attenuator level unchanged until the operator goes in and changes the setting. Perhaps I'm missing the benefit of having it change based on mode.....

Thanks ...

Scott as always, thanks.

I wasn't meaning to "blame" this on networking.....or anything. Rather I was/ am trying to understand this stuff better

Scott getting back to the dedicated NIC for the radio, I read the information you posted a number of years back on turning off stuff that isn't needed.

For the card setup, under advanced, what does need to be turned on for the interface to work with the radio? And you said, in that same post, some ...