Hi
S-ATT work correctly.
Thank you so much.

Hi

Is it possible to repeat this test.
Thank you.

https://drive.google.com/file/d/1GPtbPX ... sp=sharing

Thanks
In this option, there is no transmit mode, only receive.

EA1DAV wrote:I have a red pitaya

I also have Red Pitaya and TRX-DUO.
And where can I find out about the IP for each receiver.

Thanks Sigi
Excellent!

Hi
What could be?
No multimeter needles in transmit mode.

Hi
The size of the multimeter does not change.

Loading and starting Thetis with RX2 enabled shows a non-working RX2 S-Meter. S meter remains at -399 dBm. Changing the mode on RX2 from e.g. LSB to USB ensures that the S-meter works again. I noticed this in the TAPR release as well as in Richie's current version. Can anybody confirm this, or is t...

Thanks a lot.
This review is very helpful.
It is clear that you need to be able to directly connect a broadband antenna to view the entire spectrum.

Hi

The WB level is not correct. So it should be or not.

Thanks.
Nice button selection idea.

Active RX1, RX2, MultiRX.
Rebuilding MultiRX only with a right click works for me.

Hi

How smoothly can you tune the frequency of the "MultiRX" receiver?
Mouse wheel doesn't work.

feedbackColours.png These are how the feedback colours relate to the feedback level. I would like to swap blue and red. In my mind RED would be too hot, too much feedback level, and blue, too cold, not enough feedback. I didn't change it due to the confusion people would have after getting used to ...

Hi
Special thanks for the S-ATT RX1 (tx/rx). This logic, according to S-ATT RX2 (tx/rx), would be quite good.

I don't really think it is correct to apply 31dB attenuation for ANY mode if PS-A is off. It is ok to apply it if CW, and PS-A is off. The change has been made to and AND in rc2. Will await feedback ;) Richie. Hi. One option ATT RX1 RX2 when transmitting by default. For the PS, only the ATT of one ...

Sorry, I'll try my idea again. How to eat now Check box "ATT on TX"= ON receive S-ATT RX1=ab transmit S-ATT RX1=31 receive S-ATT RX2=ab transmit S-ATT RX2=31 Check box "ATT on TX"= OFF receive S-ATT RX1=ab transmit S-ATT RX1=ab receive S-ATT RX2=ab transmit S-ATT RX2=31 It should...

Hi
It's just that no one is working on transmission on one band and at the same time has normal reception on another band. And when there is an ATT of 31 dB during transmission, then a sensitivity dip occurs on a different range.
Sorry for my questions if they distract from the case.

This might be a change related to QSK, or a hack to add max attenuation for PS in case it is turned on? I am not sure, it was in version 2.8.8 but not in 2.8.7. Richie. When the PS mode is on, ATT is controlled by the program. Everything is clear here. In other cases, the user should be able to set...

Hi
It is not possible to set the desired value of the RX1 attenuator for transmit mode. Always set to 31 dB.
For RX2, too, at the time of transmission, there is always a setting of 31 dB. Not very convenient for transmitting on one band and receiving at that moment on another.

Hi
Richie, thanks for the video.
Even the way it works now is already good.
I would like to try everything. More commands in the TCI zzsw0, zzsw1 to switch TX from the log. If possible.

Hi
Short video TCI Thetis and log RX4HX.
https://youtu.be/ijkQQk9qbQI

Richie, I'm testing TCI with RX4HX log and I don't see any errors yet, Thethys works fine.

Hi.
ExpertSDR works with one physical receiver, there is no duplex.
Now Thetis can work normally with two physical receivers. Like two independent radios. And this is very good.

I work CW. Things are good. On spots there is a restructuring of the frequency RX1, RX2.
But, when there is a transmission of CW at the frequency RX2, then the panorama RX1 disappears. Reception of RX1 stations remains.

ramdor wrote:EDIT: yes, seems to be an old issue. I think if you switch on the checkbox 'use vac2 on split' in setup , then click on TXA and then TXB in the VFO boxes it should work.

Thanks!
That's how it works.

ramdor wrote:rx2 support is still not fully supported. Hopefully over the next few days.

Richie.

Hi
Thanks Richie
Already good!
While the transmission on RX2 is with RX1 modulation.

So did you really mean "When are TCI RX2 commands coming?" Perhaps I have misunderstandings. Now I am working on 160 SSB. At this time, reception is on 80 m FT8, even at the time of my transmission on 160 m. The communication log and the JTDX program are connected to Thetis via TCI. Again...

Thanks! TCI works!

And for RX2 there will be a СAT?

I am glad things seems to have settled today, after the changes. Thanks for the testing and all the feedback. Onto ZTB, to be honest I am not a fan of ZTB as it is all dependant on the sample rate and bandwidth of the band. Also, it becomes pointless when CTUN is off as I have mentioned in a couple...