I know this is an old post, but wondered if a solution had been found?

I have just updated from a 100D to a 7000DLE Mk2, both using the latest protocol versions available.

Using either a Pihpsdr controller or a pc running the latest Thetis the 100D has a smooth PA setting control over the ...

Not sure this the correct place, so please move if needed.

I thought I would try Thetis(v2.9.0) with my 100D (Protocol1) instead of my usual PiHPSDR and mk2 controller.

I mainly use the Anan as a transverter driver for VHF and up and but also have a 40/80m dipole connected to ANT1 and a RX antenna ...

I have a 100D and find the NR to work well when on HF bands using ANT1 but when I use the XVTR ports to connect to VHF/UHF transverters the NR just distorts the audio and makes it sound garbled and un readable?

Any one have any idea why it would do this and a possible solution?

I tried the ...

Sorry not sure where is best to post this, so please move if needed.

Can anyone confirm if there have been 2 front panels designs for the andromeda?

I have found one for sale, but it seems to have differences to the one shown for ordering from Apache direct?
The mike is a 3.5 connector not the ...

5 months later is very busy, ha ha :D
Quicker reply this time :)


With the mic bias properly applied to the electret microphone of the SB45 the mic boost option should not be required. Are you no longer using mic boost?
I am still using the mic boost, without this I have to increase the mic ...

Sorry for the delay in replying, been busy.

So maybe my comment about being RF was incorrect. So how do I stop it, I can reduce the output power to less than a watt and the problem is the same, into either a dummy load or antenna.

I have an adapter box that the SB45 plugs into and is combined with ...

I have Anan 100D running protocol 1 V6.0 and PiHPSDR V2 controller.

Recently been getting comments that my TX audio is poor and has a echo making it un readable.

I haven't changed anything and have been using a KOSS SB45 headset with the setup for months.

I initially thought is was RF getting ...

I have managed to change the encoder direction, but I had to manually edit the GPio.props file, it doesn't seem to save/use the settings if it changed using the profile on the initialisation screen.

Erik Thanks for replying.

I did try changing the settings in that part but that part seems to have all changed from the previous documented version.

The Install/update instruction are here https://github.com/g0orx/pihpsdr/blob/m ... nstall.pdf

I have a PiHPSDR controlling my Anan 100D, I have just installed the latest version 2.0.8 rc1 and it has solved the issues when using Transverter.

But my VFO know tunes the opposite way to what it did before, I remember I changed this with the previous version by changing the GPIO allocations, but ...

Many thanks for the detailed explanations, I am slowly understanding the Anan more and more.

Unless I am reading the manual wrong Pin 22 is an output the same as 10, The only pin that seems to indicate its a Input is 12 " Left Channel Line-Level Audio Input*" , but I tried that and had no success ...

I have a Anan100d with the angelia board, and PiHPSDR V2 controller.

I have the Controller connected to a PC using serial and that does the radio control for contesting. etc, I am now trying to connect the audio from the Anan to my PC so I can operate on MGM etc.

I looked at the 25 way connector ...

Erik

Thanks for the pointer I have now managed to get N1MM talking to the PiHPSDR using a serial connection.

Only issue is PiHPSDR doesn't remember the serial settings and I have to change them every time I start the software. :(

I have looked in the .props file and cant even find any reference ...

I have PiHPSDR V2 connected to a Anan100D (Angelia) and it almost works perfect( slight issue with the PA not turning off when using XVTR'ers, waiting for software update.)

I am a keen VHF contester, but recently started to contest on HF. and need to be able to interface the N1MM software with the ...

Thanks all for the information.

Laurence I wonder if you are able to supply the exact details of the ones you have used, ( drilling out is not an issues)

Regards Anthony

I have a 100d (Angelia board) and controlling with a PiHPSDR V2 Controller.

I have plugged in a Koss SB45 headset into the front MIc/Headphone socket and using a keyboard connected (not ideal) to the controller I can press the space bar for TX.

I want to use a footswitch so, using the same ...

I have built and have working the PiHPSDR controller V2, but I am struggling to find compatible knobs for the Dual Encoder EC11EBB24C03. I also can only find a knob at 30mm diameter for the VFO, I like something a little larger and finally what have other used for the case that doesn't need me to re ...