Search found 56 matches
- Sat Jun 15, 2024 6:58 am
- Forum: Thetis
- Topic: Thetis User Manual and Voicemeeter
- Replies: 3
- Views: 151
Re: Thetis User Manual and Voicemeeter
Looks like you installed VM Potato. Thetis manual refers to VM Banana. VM is a great software but tend to make things a lot more complicated than they really are for non audio professionals. How to setup depends on what you want to do. There is a lot on the forum about VM. Maybe you can try this thr...
- Fri Jun 14, 2024 7:55 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
Ok Scott it finally worked. Choosing the USB mic would not work but setting both input and output to Microsoft Sound Mapper worked. Thanks for the support.
BTW I set TX gain to 10dB for Pure Signal to work ok.
73/Sam
BTW I set TX gain to 10dB for Pure Signal to work ok.
73/Sam
- Fri Jun 14, 2024 2:25 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
Roger that Scott. So how do I go directly from USB mic to Thetis? The USB mic shows up under all drivers except ASIO but it does not matter witch driver I try USB mic wont work directly selected in Thetis Input.
73/Sam
73/Sam
- Fri Jun 14, 2024 1:02 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
So I selected Voicemeeter Virtual ASIO on both input and output in Thetis VAC 1 setup and now USB mic audio is coming ok with much less latency.
Thanks Scott.
73/Sam
Thanks Scott.
73/Sam
- Fri Jun 14, 2024 12:25 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
Ok so I uninstalled VAC and VM Banana and installed VM Potato. So now selecting ASIO in Thetis VAC 1 setup I get RX audio to VM Potato. I can then feed that RX audio for example to my PC speakers. The USB mic is on VM Stereo input 1 and I can also direct audio from USB mic to PC speakers. But how do...
- Fri Jun 14, 2024 7:48 am
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
Ok Scott here are my settings using the USB mic on VM Hardware Input 1. Audio TX is fine besides the short delay. So if I activate ASIO in Thetis VAC 1 setup then what should the settings be in VM Banana?
73/Sam
73/Sam
- Thu Jun 13, 2024 5:42 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
Thanks for the reply Scott. Yes I started following that instruction but USB mic would not work when selecting it in Thetis VAC1. Installed a pair of VAC:s and could then feed Voicemeeter Banana A1 to Line 1 and then select Line 1 in Thetis VAC input. The audio delay is pretty long, guess I will hav...
- Thu Jun 13, 2024 5:29 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
Guess I was too much trigger happy. Downloaded a pair of VAC and now I can feed the audio via Voicemeeter Banana to Thetis.
73/Sam
73/Sam
- Thu Jun 13, 2024 3:27 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: USB mics straight into PC
- Replies: 22
- Views: 9345
Re: USB mics straight into PC
I wanted to try a USB mic just for fun but having problem getting the mic audio into Thetis. The USB mic installed correctly and works fine when checking in Windows. Also shows up in Voicemeeter Banana so selecting the new USB mic in Hardware Input 1 I can then feed audio to hardware output and for ...
- Thu Jun 06, 2024 7:42 am
- Forum: Apache-specific Hardware Discussions
- Topic: Andromeda drive power drop in low power mode
- Replies: 8
- Views: 2051
Re: Andromeda drive power drop in low power mode
Hi Guys, Just want to let you know I fixed the problem with fluctuating output. I cleaned the SMA connectors as Rob suggested but that did not help. I then pressed the SMA/f connector on the PA-board (TX input) pretty hard while transmitting and the fluctuation stopped. So I demounted the PA-board a...
- Mon May 27, 2024 3:06 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Thetis & CW Skimmer
- Replies: 9
- Views: 1292
Re: Thetis & CW Skimmer
Here are my settings. Using VoiceMeeter VAC. Works great.
- Wed May 22, 2024 4:43 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: N1MM: Radio goes into TX mode when in S&P mode
- Replies: 7
- Views: 764
Re: N1MM: Radio goes into TX mode when in S&P mode
I did a video a year ago on my settings with Thetis and N1MM. CW, SSB, RTTY with MMTTY and WSJTX. Works great.
https://www.youtube.com/watch?v=NCvH_-TO6Ks
73/Sam
https://www.youtube.com/watch?v=NCvH_-TO6Ks
73/Sam
- Thu May 16, 2024 3:08 pm
- Forum: Apache-specific Hardware Discussions
- Topic: Andromeda drive power drop in low power mode
- Replies: 8
- Views: 2051
Re: Andromeda drive power drop in low power mode
Hey Rob, thanks for the feedback and suggestions. Checking the SMA connectors will be a good starting point.
73/Sam
73/Sam
- Mon May 13, 2024 8:07 pm
- Forum: Apache-specific Hardware Discussions
- Topic: Andromeda drive power drop in low power mode
- Replies: 8
- Views: 2051
Re: Andromeda drive power drop in low power mode
Here is a video of the power fluctuation with 10W DRIVE into a dummy load. with 100W power output is fairly stable but sometimes drops to 40-50W. 10W drive is stable when station is cold but start fluctuating as soon as it warms up. Its impossible to use the SPE Expert 1.3K-FA amp that requires 10-1...
- Wed Apr 24, 2024 3:03 pm
- Forum: Apache-specific Hardware Discussions
- Topic: Andromeda drive power drop in low power mode
- Replies: 8
- Views: 2051
Re: Andromeda drive power drop in low power mode
Have tried resetting database and also trying older saved versions of Thetis but that did not help. I think it´s a hardware issue or a bad solder point. Have been running only 5-10W drive for over a year so maybe the hardware doesn't like running idling all the time
- Wed Apr 24, 2024 6:45 am
- Forum: Apache-specific Hardware Discussions
- Topic: Andromeda drive power drop in low power mode
- Replies: 8
- Views: 2051
Andromeda drive power drop in low power mode
Hi guys, have a problem that stared occurring a few weeks back. Have Andromeda running Thetis 10.3.6 and protocol 2 v2.2.3. Have a Expert 1.3K-FA amplifier and it only needs about 10W drive. For some reason drive power began dropping to zero in the middle of TX session. This occurs intermitted so I ...
- Thu Jan 04, 2024 9:47 pm
- Forum: Remote Operation Over The Internet
- Topic: Thetis connect via VPN ???
- Replies: 19
- Views: 7593
Re: Thetis connect via VPN ???
Ben, were and how did you buy the Anvelina PROII/III?
73/Sam
- Sat Aug 26, 2023 7:47 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: ANAN 7000 MK 3 - Ciclone V- P.2 issues
- Replies: 7
- Views: 7220
Re: ANAN 7000 MK 3 - Ciclone V- P.2 issues
Stefano, I had the same problem with SEQ errors after updating to P2. The problem was solved when I installed the FM patch, see this topic https://community.apache-labs.com/viewtopic.php?f=9&t=4486&p=23175&hilit=73%2FSam#p23175 At least its worth trying. 73/Sam Tnx Sam, until know why y...
- Wed Jun 28, 2023 7:52 pm
- Forum: Apache Labs News
- Topic: ANAN-G2 Shipping Update
- Replies: 319
- Views: 3204257
Re: ANAN-G2 Shipping Update
Fool me ounce shame on you. Fool me twice shame on me. Anyone reading this forum should know Apache-labs has zero customer relation or support. If they say delivery starts June 10 deliver could be anywhere between 1-12 months. Is no use sending e-mails or posts on this forum, they will not response....
- Thu Jun 15, 2023 9:11 pm
- Forum: Apache Labs News
- Topic: Shipping Updates
- Replies: 255
- Views: 363464
Re: Shipping Updates
wz3hmt wrote:oh boy, 15 more days until end of June.
Will we see the ANAN-G2-1K shipping soon?
Most probably not.
- Mon Apr 24, 2023 10:15 pm
- Forum: Amplifiers & Tuners
- Topic: ICOM PW1 CIV with ANAN 7000DLE MKII
- Replies: 12
- Views: 8532
- Sat Apr 22, 2023 4:55 pm
- Forum: Thetis
- Topic: Thetis v2.9.0.8 - meters and then some more
- Replies: 158
- Views: 56322
Re: Thetis v2.9.0.8 - meters and then some more
That issue should be solved in v2.9.0.19.
See [https://github.com/sjk7/Thetis-2.9.0/issues/18][/url]
See [https://github.com/sjk7/Thetis-2.9.0/issues/18][/url]
- Thu Apr 20, 2023 7:14 am
- Forum: Thetis
- Topic: Monitor audio feedback loop
- Replies: 0
- Views: 2066
Monitor audio feedback loop
Andromeda -CIV Thetis 2.9.0.8 FW v2.1.26. I have a problem when using TX audio monitor. Pressing MON and TX I get a awful feedback loop. Same as if I would have put the microphone to the speaker and turn up full AF volume. I have to turn Master AF down to 1 or 2 to get rid of the worst feedback loop...
- Wed Apr 19, 2023 2:21 pm
- Forum: PureSignal Operations (PowerSDR & Thetis)
- Topic: Solved! Pure Signal Does not work on Protocol 2 - 7000 MKIII
- Replies: 8
- Views: 6450
Re: Pure Signal Does not work on Protocol 2 - 7000 MKIII
How do you think it got changed from the defaults?
P1 had a different SetPk value that I don't remember. This was several months ago. After installing P2 the old SetPk value was still precent. Clicking Default changed the SetPk to 0.2899 and PS was working fine again.
How and why I don't know.
- Wed Apr 19, 2023 12:46 pm
- Forum: PureSignal Operations (PowerSDR & Thetis)
- Topic: Solved! Pure Signal Does not work on Protocol 2 - 7000 MKIII
- Replies: 8
- Views: 6450
Re: Pure Signal Does not work on Protocol 2 - 7000 MKIII
I had the same problem first time I installed P2. It turned out I had to press Default and change the value in SePk. Should be 0.2899.
- Sat Apr 15, 2023 1:37 pm
- Forum: Thetis
- Topic: Understanding G7KLJ 2.9.0.11 release
- Replies: 127
- Views: 29728
Re: Understanding G7KLJ 2.9.0.11 release
Guys, But I don't want to be an unpaid volunteer for Apache-Labs ad inifinitum. Its not like their radios are a fiver. Great business model for them, thou ;-) Steve When someone from the outside enters the forum they discover Apache-Labs flawed business model that relies addicted software users and...
- Sun Apr 02, 2023 11:20 am
- Forum: Apache-specific Hardware Discussions
- Topic: Saturn: A New Apache Labs SDR Transceiver (ANAN-G2)
- Replies: 82
- Views: 34865
Re: Saturn: A New Apache Labs SDR Transceiver (ANAN-G2)
[quote="K1CWD"]The big problem with the Orion architecture is that it is seriously limited in that the "protocol" is implemented in a very difficult to change FPGA. A change for example to a potential "protocol three" would require the support of very good FPGA develope...
- Tue Mar 28, 2023 7:01 am
- Forum: Thetis
- Topic: Thetis v2.9.0.8 - meters and then some more
- Replies: 158
- Views: 56322
Re: Thetis v2.9.0.8 - meters and then some more
Here is my layout. Its a joy everyday when Thetis comes alive.
- Wed Mar 22, 2023 3:42 pm
- Forum: Thetis
- Topic: Thetis v2.9.0.8 - meters and then some more
- Replies: 158
- Views: 56322
Re: Thetis v2.9.0.8 - meters and then some more
Richie, what a great job, and what a great software. Its true joy using Thetis and the latest update with the beautiful meters. Its amazingly fantastic and great fun to use. Here is a video I just recorded listening to CY0S 15m CW trying to find RX QRG. [youtube]https://www.youtube.com/watch?v=XkVCo...
- Mon Mar 13, 2023 7:56 am
- Forum: Apache-specific Hardware Discussions
- Topic: Abrupt reduction of noise floor on receive
- Replies: 55
- Views: 23946
Re: Abrupt reduction of noise floor on receive
Try connecting another receiver to the circuit or different antenna. I had a similar problem some years ago. RX would suddenly drop. A short TX brought RX back. It was a bad connector on the antenna feedline.