w-u-2-o wrote:If it's truly wired as discussed, then the only thing I have left to offer is that if you've got the mic PTT button wired up, then unwire it from the TRS connector and see if that fixes the problem.

Yes good idea will try that in the morning since i don't use the ptt on the mic.

When I wired a Heil BM-10 with XLR connector I asked Heil about the XLR pins. The response from Heil was: PIN1: MIC GND PIN2: MIC PIN3: PTT PIN4: PTT GND 73/Sam Hi Sam, I requested the pinout from Heil for the gm4 mic. Meanwhile in the morning I am going to try a cheap radio shack mic I have it's j...

When I switched mic+ from tip to ring I also switched it in the Thetis, or it would not pass mic audio. And it is wire as you stated.

Yes the cable is custom and the gm4 is 4 pin xlr with pin 4 being ptt 1,2,3 being standard. I read here and heil in bridging pin 1 and 3. I am using ptt at rear of radio via foot switch. Originally when I noticed the click in the element mic+ was on tip and ptt on ring. I flipped the two but still s...

I flipped the mic signal to ring and it seems like the click is less but a bit noticeable.

Jay n2gq

I am using a Heil gm4 dynamic mic.
The mic signal is connected to the tip and selected in menu. Bias off and ptt is on I use a foot switch. When I activate ptt with mox icon I don't get the click in the element. I have bridged 1 and 3 at both ends of mic cable to remove the hum.

Jay n2gq

I have a click coming from my mic element when I ptt. Has anyone come across this? My boom and mic just happened to be near my ear when I heard this. Radio is 7000dle mk3.
Jay n2gq

I am going to try a PS test today. Hopefully if I get time. Are any of you guys operating with a new mk3 chip and had any success?

Jay n2gq

Yes you are correct about sample rate. When at the largest sample I can't enable diversity. But when I lower to 768.... sample rate then it works.
I don't have a sampler for the pure signal yet so I don't know how it affects it but i'm sure as you said there will be a limitation.

Jay n2gq

Good evening, Okay this is what I did and the sequence errors have gone away. I went into tp-link network card properties and disabled most of the parameters that were enable. Now what actually helped is the parameter [Speed & Duplex] which I set it to 100mbps full duplex not 1000 gbps. And I sw...

I feel your pain, this is unsat. also W2UO wrote There is no "issue" with the Mark III and Protocol 2 per se. There are issues with Protocol 2 overall. P2 firmware puts greater demands on both the FPGA (to achieve timing closure) and the Ethernet connection (Gigabit speeds and UDP packet ...

Okay I will try some of those settings I hope I get something going. Will keep you posted.
Thank you
Jay n2gq.....

Are the seq errors resulting in any noticeable degradation of your transmit audio? If not then you can ignore them. Public/private doesn't really matter. In Thetis Setup > General > H/W Select have you enabled Network Throttle Index Tweak? You can try disabling Windows Firewall on the dedicated TP-...

Hi I received my Anan-7000dle mk3 tuesday. I installed protocol 2 firmware and latest thetis and installed the patch as well for fm/eer. I have a dedicated tplink network card for the radio. I also followed w1aex static ip instructions. I also configured card for ipv4 only with the npcap only. Okay ...

Hi,
Have you checked the power pole connection? Are they getting hot?
n2gq

Hi
Curious, if you received the radio yesterday it should be a mkIII? I am waiting on mine and was wondering if that was the case and firmware failure?

Jay n2gq

Thanks Larry getting shack ready today for the new addition.

Jay n2gq

Thanks for your response. I ordered mine today settled on 7000.

Jay n2gq

One more question how about the tun button when I tune my amp, which is an ameriton al-82 Ineed different levels of tun power till I reach max power. Can I adjust the tun power output from the controls in the gui.

n2gq

Okay thank you, love the reviews and excited about the radio. Going to consider between 7000 and 8000.

n2gq

Hi I'm not familiar with this radio and interested in purchasing. I currently have a flex-6300 in which I can see 7mhz at a clip if I need to. How much spectrum can the Anan 7000 see at once? And how well does it network, like if I'm in another room can I use my laptop to log onto radio? Thank you n...