Hi When using the flex control wheel running with ddutil for the vfo, and when I have the tune step at 100hz it moves 250hz. If I use a 50hz tune step it then tunes at 100hz. If I try 250hz it moves 500hz. With the mouse it works fine. I tried setting the ddutil to 1hz. to make sure it is not creati...

I really like the ELAD TM-2... It has a small LCD screen that shows the frequency / mode / signal strength. I set the background LED to blue when VFO A is selected and yellow when VFO B. Transmit turns the LED Red. There are knobs for vol / mult / VFO. My favorite part is that I can set VFO A to th...

The list will be vastly increased as I have just fixed an issue where more modern controllers give additional 14bit midi messages for sliders/controllers. The messages for those knobs/sliders arrive in pairs and the midi config was getting confused. As a quick fix we are now ignoring the 14bit mess...

Will join you some morning all sound good on youtube video.

Hi,
Does anyone know the latest midi controllers that are selling new, that work with Thetis?

When I was having a issue with my 7000dle mkIII and protocol II I went into the network card setting and reduced it down to 100mbps with a bandwidth of 768000. And I still run 768000 just to keep it tamed. I no longer have to run the nic card at limited 100mbps after the latest firmware. I hope som...

I had the same issue with rf. But my problem, the mic wiring was wrong. I use a Heil Gold line mic, and of course I reversed the mic + lead. But it made me re-do the shack ground a lot nicer. Finally fixed the mic issue.

When I was having a issue with my 7000dle mkIII and protocol II I went into the network card setting and reduced it down to 100mbps with a bandwidth of 768000. And I still run 768000 just to keep it tamed. I no longer have to run the nic card at limited 100mbps after the latest firmware. I hope some...

I am going to try a PS test today. Hopefully if I get time. Are any of you guys operating with a new mk3 chip and had any success? Jay n2gq Jay--AFAIK, you are the only person with the most recent FPGA that has reported an intractable problem with a GigE connection. I'm pretty sure it's my same pro...

You can use an adapter 3d printed 50mm down to 40mm if you have the space. There are several on the following site. But can be adjusted. https://www.thingiverse.com/thing:2037140 I'm not sure I can get enough air from two 40mm fans without "fan scream", but it would be a cheap enough expe...

I know it sounds weird but when I get up off my chair my receive drops. I am thinking static, although I was not touch anything. If it consistently and reliably does that then it certainly sounds like a static discharge of some sort. How is your station grounding and bonding? The station ground and...

You can use an adapter 3d printed 50mm down to 40mm if you have the space. There are several on the following site. But can be adjusted.

https://www.thingiverse.com/thing:2037140

I know it sounds weird but when I get up off my chair my receive drops. I am thinking static, although I was not touch anything.

Interesting. If you switch to an empty antenna port does the panadapter look like it does when the problem is happening? Okay here is a video showing receive drop problem and then a selection to an empty antenna port. https://youtu.be/JxXN8J40Xs0 It is funny it seems to happen when I get up off my ...

Interesting. If you switch to an empty antenna port does the panadapter look like it does when the problem is happening? I am going to check if it does. On Saturday it seemed like the radio really freaked out a bit I was not sure what was happening. So I had a windows update in cue and took care of...

Well, it happened again this morning and I heard the relay click two times. This time I went to setup and antennas the 20mtrs selected ant 2 then ant 1 and it became normal again. Maybe has something to do with antenna selection? This happened while receiving.

Are you going to try my suggestions? It does suck going back to P1, but it's probably a worthy experiment to see if is somehow tied to firmware. This might be related to the other reported problem with the Cyclone V P2 firmware associated with jumps in freq. calibration. Well, I might if it happens...

w-u-2-o wrote:What precipitates the drop in the noise floor? A transmit-to-receive transition? Or does it just spontaneously drop in the middle of receiving?

Just during receive so far, it happened twice yesterday and nothing today. This is the third time it happened.

Will fix, now public.

I just installed the latest 2.9.08 meter thetis yesterday and while listening my receive dropped as well a quick keyup brought it back up. I did hear the relay switch when it happened. This is the first time this has happened. I have protcol 2 and a 7000del mkIII. I duplicated this by actually swit...

Every once in a while, I hear a buzz and a relay click which is very fast almost like an interrupt.
Has anyone experienced this?

KA9UVY wrote:Thanks Jay, I purchased a tiny SA and calibrated mine this evening.

The tiny SA will be handy to have here anyways, thanks for the tip on it.
73, Robert
KA9UVY

Cool, glad it worked for you as well.

Hey Jay, Be sure and let us know if the S9 signal generator works out for you... I tried an old signal generator I had here and it failed to work. I see the S9 sig generator has some different freq available but none of which are on even Mhz. Thetis didn't let me put in anything other than the Mhz ...

Hey Jay, Be sure and let us know if the S9 signal generator works out for you... I tried an old signal generator I had here and it failed to work. I see the S9 sig generator has some different freq available but none of which are on even Mhz. Thetis didn't let me put in anything other than the Mhz ...

Okay Scott
Thank you....

When calibrating the s-meter is a 1k tone used or just unmodulated carrier?

Glad you got it all sorted! :) PureSignal tells no lies! Please tell Tyler I also say "Hi!" [thread drift] My audio software setup is perhaps more complex than it needs to be. Presonus Studio 192 Mobile interface <---->Voicemeeter<---->Reaper DAW Thetis<-----------------------------------...

HI Scott, Finally got the distortion sorted. I had to work all my ground in the station everything now goes to a common point. Used a morgan line arrestor for the rotor at my hexbeam. In my case seems like a lot of the rf energy was on the control cable for rotator. But anyway, the radio is working ...

The adjustable CleanRF samplers are not recommended as it is all too easy to accidentally adjust them to dangerous feedback output levels that can damage the ANAN. Be careful with it! Have you tried changing to the 70 & 190Hz combination? There should be no problem with the power calibration. U...

[quote="w-u-2-o"]When you say "I get distorted audio", how do you know this? If you are listening with MON, it will sound distorted to you because you are hearing the raw DAC data and when PS is enabled that DAC data is, of course, pre-distorted! Or is somebody reporting this to ...