Use the Thetis built-in keyer but keep the Winkeyer attached. See if it locks up with that. If it does then disconnect the Winkeyer and try the built-in keyer again. If it works ok then it seems like it might be RFI associated with the Winkeyer.

This is starting to sound like an RFI problem.

Is N1MM keying the radio via Thetis and a virtual serial cable? Or is it using hardware keying of some kind?

Checked so far: correct ADC, bad database, old versions. Here's a couple of other ideas: - Perhaps there is a fault with the bandpass filters for the RX2 input. You might try selecting the bypass state on those. - Remove the covers and check for any loose RF connections or cables. Did RX2 ever work ...

In this video there is also some mention of improved NR and NB modes, but no specifics.

PayPal might suspend Apache for having an excessive dispute rate...

See this tacked thread: viewtopic.php?f=9&t=4707

The 200D has the original Orion board, not the Orion MKII. Schematics for the Orion can be found in the schematics section of this forum.

AFAIK, all boards from the Hermes to the Saturn output 500mW max. on 160-10M, and 350mW max. on 6M.

AFAIK there is no off-the-shelf product available at this time. In a pinch, you can use a shelf, mount it up with a blank panel over the front of it, and cut an appropriately sized opening in the front panel. Or, even better, order something like this (there are a million choices) and, again, cut an...

Glad you got it sorted

Now that you know unambiguously which FPGA you have, take a look at the following topic:

viewtopic.php?f=32&t=4588

There are some slightly newer versions available to you that fix a QSK bug.

Well I didn't know there was actually a law relating to my issue " Segals law" but its true enough. All I wanted to do was to set up my oscillator (out of a serious GPSDO) to an accurate 10 MHz to use on my 7000 mkII. It turns out that its not a simple task. Absolutely right. Welcome to t...

...the two GPSDO's are moving in different directions at slow but similar speeds it can't be the oscillator causing that. Either one or both of the GPSDOs is either broken or a bad design. It's as simple as that. I have two GPSDOs here, an older BG7TBL unit (Chinese, from eBay), and one from Leo Bo...

Tests that I've done imply that the 10MHz signals from the GPS satellites are changing frequency randomly by small amounts. I can assure you this is not the case. I have been deeply involved with the GPS and, in particular, GPS time and frequency standards, since before GPS reached it's Initial Ope...

I'm confused. First you write: Downloaded the file. 1019_Metis_Orion_MkII_Protocol_2_v2.0b.zip. Then you write: Metis_Orion_MkIII_Protocol_2_v2.1.26c.rbf...That is what I programmed. Which is it? Or did you try both? Four things to consider: 1. If Bootloader runs OK, then you did not brick the unit,...

See this topic: viewtopic.php?f=32&t=4462

Download the manual from the front page of the Apache website (https://apache-labs.com/) and Page 12 should answer all your questions.

Short answer is "yes".

Gents:

Let's please keep this topic on target, which is the discussion of G2 deliveries.

Thanks,

Scott

Have you power cycled the 7000?

With the bottleneck being the FFT processing, it's unlikely you can get Thetis to run much faster than 60Hz at 384KHz or larger IF bandwidth. Thus a faster display is wasted on Thetis, but you may find it valuable for gaming.

It would probably be better to switch it to a 50 ohm load when not in use.

AFAIK this is not user-adjustable separately.

Editing the band plan might be a work-around. More info here: viewtopic.php?f=9&t=5021&p=29026

I took a look at the problem this morning and it definitely appears to be a bug. Selecting "extended" allows Thetis to go into transmit mode but no RF power is produced. This is in contrast to the behavior when extended mode is not selected whereby Thetis will not even go into transmit mod...

Not 100% certain of what you are trying to say, but just in case it is relevant there is no bias voltage (phantom power) available on the G2 balanced TRS mic input.

PureSignal can use the entire range of the step attenuator, which is 0 to 31 dB in 1 dB steps.

However, remember not to exceed +13 dBm at the rear panel input to avoid the risk of damaging something.

Unfortunately I don't know what the coupling factor is for the internal coupler.

From a linearity and measurement accuracy perspective +/-1dB is pretty good for the hardware we've got.

Hi Tom, The only way to know for certain what's what is to get some trustworthy (calibration you are confident of) test equipment and start making measurements. Measure the output of the coupler. Put a calibrated signal into the ANAN and run the level calibration routine. Then put that calibrated si...

MIDI controllers normally only connect to one app at a time. First app wins. For instance, I am able to use my Hercules DJControl Compact with both Thetis and Voicemeeter but not at the same time. However, as you might expect, people have come up with solutions for this very obvious limitation. I do...

There is an excellent hi-res photo here: https://www.dl6ka.de/anan.htm

Look in the bottom right corner.

Headers and jumpers are standard 0.1" pin spacing.

k3rw wrote: Sounds like a worthy addition to the 10E. How do I know if my 200D is one of those that does not have a switched feedback path (serial #, some other way?)?

See viewtopic.php?f=17&t=2387&p=2557

Wow, I'm surprised these can still be purchased! I don't have an ANAN-10, but I do have a 100D and it also required a similar modification for good PureSignal performance. I built my own version. IMHO the TR-Plus is a worthy accessory. It's definitely necessary for PureSignal because the older desig...