Search found 36 matches
- Tue Nov 29, 2022 11:10 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes Setup Problems
Hi Scott, Thank you very much for your comments as usual. I've read User Manual of Hermes V1.8 as described in my previous message. I had to pay attention to the latest manual V1.18 . The schematic and the contents of the manual regarding DC Supply Jumpers has no discrepancy. Thank you again. 73, To...
- Mon Nov 28, 2022 7:52 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes Setup Problems
Hi Sigi, Thank you for your input and reminding me of the schematic. Would you like to say that the manual about DC Supply jumpers setting is incorrect? The question is which is correct, the manual or the schematic. In case that the schematic is right, then how do we put the jumpers in order to make...
- Sun Nov 27, 2022 11:33 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes Setup Problems
Hi Sigi,
I submitted the question hastily.
Sorry about that.
Tokio
I submitted the question hastily.
Sorry about that.
Tokio
- Sun Nov 27, 2022 11:30 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes Setup Problems
Hi Group, I have a problem about DC Supply of Hermes 14-bit board. The default is 13.8 V to pin 1 and pin 2 of J10 of the board. DC12V and DC5V can be also fed to this connector: pin1 : 12V, pin 4: 5V in the manual. According to the Hermes manual Revision 1.8, page 10 and page 12, the following jump...
- Sun Nov 27, 2022 11:09 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes Setup Problems
Hi Group, I have a problem about DC Supply to Hermes board. The default is 13.8 V to pin 1 and pin 2 of J10 of the board. According to the Hermes manual Revision 1.8, page 10 and page 12, the following jumper setting explained with the input DC Supply: DC Supply (case1)13.8V (case2)12V (case3)12V an...
- Fri Nov 25, 2022 11:47 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes (10E and 100B) Protocol 2 Firmware Topic
Hi Scott, Thank you for your comments. Just after reading your comments, I realized Roaming data path was incorrect. For the test, I use a different PC from my ordinary PC for QSO. I corrected the path for database and binary file. Running different versions on a PC requires this attention. Then, I ...
- Fri Nov 25, 2022 11:41 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes (10E and 100B) Protocol 2 Firmware Topic
Hi group, I have done test( only for receiving) here in my environment. The result is the following: <<10E Firmware ver10.4_pre2>> Thetis 2.8.11 works apparently fine . Thetis 2.9.0.6 works, but VAC not. This is the same as the firmware10.3. <<10E Firmware ver10.3>> Thetis 2.8.11 works apparently fi...
- Fri Nov 25, 2022 4:15 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes (10E and 100B) Protocol 2 Firmware Topic
Hi Scott, Thank you for your input. As for Thetis 2.9.0.6 with 10E, please look at the following screenshot. Thetis 2.9.0.6 is dumb without any response, no spectrum. thetis2906_10e_resized.png On the contrary, Thetis 2.8.11 is working. thetis2811_10e.PNG As for the MAC address, both Thetis show a s...
- Thu Nov 24, 2022 2:31 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes Setup Problems
- Replies: 14
- Views: 8655
Re: 14-bit Hermes (10E and 100B) Protocol 2 Firmware Topic
Hi All, I received a special production Hermes 14 bit board yesterday. The firmware installed is Protocol 1 Hermes v1.5. With this firmware, PowerSDRmrx3.4.9 as well as Thetis v.2.8.11 are working apparently. But Thetis v2.9.0.6 does not work. So, to change the firmware of this board(10E) to Protoco...
- Thu Aug 18, 2022 7:21 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Thetis ZZSM0 not working on TCP/IP CAT
- Replies: 4
- Views: 3240
Re: Thetis ZZSM0 not working on TCP/IP CAT
Hi Ernst, Thank for your confirmation. I confirmed your result. Now I can get the correct reply from Thetis as you showed. I'll try a speech synthesize of S-meter reading and frequency. One of my friends has an eyesight problem, so he cannot read the S-meter nor Frequency. I've heard that IC-7800 co...
- Tue Aug 16, 2022 7:59 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Thetis ZZSM0 not working on TCP/IP CAT
- Replies: 4
- Views: 3240
Re: Thetis ZZSM0 not working on TCP/IP CAT
Hello All, My post has been resolved. My code of Python was not adequate. I confirmed the very correct reply from Thetis regarding ZZSM0/ZZSM1. Therefore I can proceed to the next step of my project. So far I used to use C# socket program. Python is quite convenient, but is very new to me. FYI, I at...
- Tue Aug 16, 2022 7:33 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Thetis ZZSM0 not working on TCP/IP CAT
- Replies: 4
- Views: 3240
Re: Thetis ZZSM0 not working on TCP/IP CAT
Hello All,
My simple python socket may cause the trouble to receive an inadequate response...
But, does ZZSM1; return ZZSM1xxx; ?
73,
Tokio
JA1CCA
My simple python socket may cause the trouble to receive an inadequate response...
But, does ZZSM1; return ZZSM1xxx; ?
73,
Tokio
JA1CCA
- Tue Aug 16, 2022 6:28 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Thetis ZZSM0 not working on TCP/IP CAT
- Replies: 4
- Views: 3240
Thetis ZZSM0 not working on TCP/IP CAT
Hello Richie and All who may be concerned about CAT interface on TCP/IP, Thanks to Richie's effort, we can enjoy CAT interface on TCP/IP. In this regard, recently, I've written Acom-2000A auto-tuning program working on a PC. It works fine with Thetis (v 2.9.0.6) to get the Thetis frequency as well a...
- Thu May 19, 2022 11:24 pm
- Forum: Thetis
- Topic: Thetis v2.9.0 - Updates and Issues
- Replies: 431
- Views: 109530
ATT on TX synchronized to PS attenuation
Hello All, Several weeks passed after I changed Thetis from v2.8.11 to v2..9.0.6. I report about "ATT on TX" function I didn't expect. Once I set it to 31dB, it becomes e.g., 10dB just after I executed Pure Signal. This 10dB is equivalent of PS attenuation. In v2.8.11 I remember this ATT f...
- Thu Apr 28, 2022 9:39 pm
- Forum: Thetis
- Topic: Thetis v2.9.0 - Updates and Issues
- Replies: 431
- Views: 109530
Re: Thetis v2.9.0 - Updates and Issues
Hi Scott,
Thank you for advice. I neglected unchecking Bypass. Now it works.
Thank you again!
73,
Tokio
Thank you for advice. I neglected unchecking Bypass. Now it works.
Thank you again!
73,
Tokio
- Thu Apr 28, 2022 12:48 pm
- Forum: Thetis
- Topic: Thetis v2.9.0 - Updates and Issues
- Replies: 431
- Views: 109530
Re: Thetis v2.9.0 - Updates and Issues
Hi Richie, Thank you for your update of v2.9.0.6. I tested it with Alex using my Hermes(TAPR) board. Unfortunately Alex is not working with v2.9.0.6. On the contrary, Alex is fine with v2.8.11. Please look at the pictures. When RX, Alex filter functions as for LPF, not BPF. You see the difference. I...
- Tue Oct 26, 2021 9:13 pm
- Forum: Thetis
- Topic: Thetis v2.8.11 - UPDATES and current issues
- Replies: 1752
- Views: 874877
Re: Thetis v2.8.11 - UPDATES and current issues
Hi nubbyless, Thank you for your comment on my posting. Low Res on PS Amp View panel is for resolution. It doesn't affect the issue I posted. I suppose the problem would be related to the baseband (audio) processing modification in Richie's development. In addition, in 21j PS improvement is lower th...
- Mon Oct 25, 2021 12:51 am
- Forum: Thetis
- Topic: Thetis v2.8.11 - UPDATES and current issues
- Replies: 1752
- Views: 874877
Re: Thetis v2.8.11 - UPDATES and current issues
Hi Richie, All, From yesterday I started to use the update version here. I would like to report the comparison between Thetis original 2.8.11 and the updates on Pure signal and TX/RX sound. First of all, PS Amp View is strange between them. Please look at the screenshot. In 2.8.11, Mag. Corr. curve ...
- Sun Oct 24, 2021 3:36 am
- Forum: Thetis
- Topic: Thetis 2_8_11 changes/ideas/wants/wishes
- Replies: 304
- Views: 96373
Re: Thetis 2_8_11 changes/ideas/wants/wishes
Hi Ramdor,
I've found Recover Tune Step Option in Misc of Option-1.
It works fine.
Thank you again.
73,
Tokio
I've found Recover Tune Step Option in Misc of Option-1.
It works fine.
Thank you again.
73,
Tokio
- Sun Oct 24, 2021 2:57 am
- Forum: Thetis
- Topic: Thetis 2_8_11 changes/ideas/wants/wishes
- Replies: 304
- Views: 96373
Re: Thetis 2_8_11 changes/ideas/wants/wishes
Hi Ramdor,
I really appreciate your great works to enhance Thetis.
Is your update below for the TUNE STEP by mode?
[done_21j]30) Step size stored against mode
I've just updated Thetis 2.8.11 original to 21k7. I'm not able to have TUNE STEP by mode.
73,
Tokio
JA1CCA
I really appreciate your great works to enhance Thetis.
Is your update below for the TUNE STEP by mode?
[done_21j]30) Step size stored against mode
I've just updated Thetis 2.8.11 original to 21k7. I'm not able to have TUNE STEP by mode.
73,
Tokio
JA1CCA
- Mon Aug 30, 2021 2:56 am
- Forum: Thetis
- Topic: Thetis 2_8_11 changes/ideas/wants/wishes
- Replies: 304
- Views: 96373
Re: Thetis 2_8_11 changes/ideas/wants/wishes
Hi Great Developers,
I'm using Thetis V2.8.11 for SSB as well as for CW.
My wish is Tune Step should be set to100Hz when CW selected. 1kHz is set again when SSB. mode. SDR Console V3 adopts this scheme.
Is this already considered as one of the change list?
73,
Tokio
I'm using Thetis V2.8.11 for SSB as well as for CW.
My wish is Tune Step should be set to100Hz when CW selected. 1kHz is set again when SSB. mode. SDR Console V3 adopts this scheme.
Is this already considered as one of the change list?
73,
Tokio
- Mon Jun 28, 2021 4:59 am
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Hi Scott,
Thank you very much for your prompt reply.
I'm following the URL you mentioned.
You are very competent pathfinder I really appreciate.
73,
Tokio
JA1CCA
Thank you very much for your prompt reply.
I'm following the URL you mentioned.
You are very competent pathfinder I really appreciate.
73,
Tokio
JA1CCA
- Sun Jun 27, 2021 9:21 pm
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Hi Scott, According to your advice about feedback level, I increased it by 2dB this time. My sampler uses 2 stage ATTs after Tandem match, 23dB, and 2dB. I removed 2dB ATT. For 23dB, I use 56 ohms 1W chip resistor (56 - 330 - 56: 23dB pi ATT) . To get 4dB increase, I have to replace this 23dB ATT by...
- Thu Jun 24, 2021 9:49 am
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Scott, This evening I checked the spurs on 3.510 900 which was shown in the previous screenshot. You mentioned 31dB S-ATT on the picture. 31dB is set because that ATT on TX is set to 31dB in the setup panel << General->Ant/Filters->Antenna >>. In addition, this is TX by TUNE. In TUNE transmission Pu...
- Wed Jun 23, 2021 11:34 am
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Scott, Thank you for your question and advice. 1) Sorry, I didn't pay much attention on S-ATT 31dB case. Yes, it is very strange. But, I couldn't remember exactly the set-up situation. I check again the 100W output case where it was 31dB S-ATT. 2) The actual S-ATT for 1KW is around 18dB that I confi...
- Wed Jun 23, 2021 7:06 am
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Scott, I measured the output of Orion MKII and also that of Munin3. You are partially right. Since there are no spurs at the output of Orion MKII nor Munin3. I tested as follows; Step 1: I confirmed the spurs on Thetis DUP by TUNE on 3.510 900. We can see the spurs as attached picture. Step 2: I mea...
- Wed Jun 23, 2021 3:16 am
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Hi Scott, Thank you very much for your reply. 1) As for Pure signal, to get more performance of pre-distortion, my current feedback level could be increased by reducing the coupling. That means S-ATT for 1KW should be 24dB(6dB up), as well as for 100W S-ATT be 13dB reading. I'll try to get more feed...
- Tue Jun 22, 2021 11:24 pm
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Hi Scott,
S-ATT during 1kW output is around 18dB, not 4-5dB. My memory wasn't correct;
S-ATT for 1K in TX: 18dB
S-ATT for 100W : 7dB.
FYI, the 1KW amplifier is an old TL-922, 2x3-500Z.
Please refer to the attached pictures.
73,
Tokio
JA1CCA
S-ATT during 1kW output is around 18dB, not 4-5dB. My memory wasn't correct;
S-ATT for 1K in TX: 18dB
S-ATT for 100W : 7dB.
FYI, the 1KW amplifier is an old TL-922, 2x3-500Z.
Please refer to the attached pictures.
73,
Tokio
JA1CCA
- Tue Jun 22, 2021 10:10 pm
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Hi Scott, Thank you very much for your input. > Do you have a coupler at the output of the Munin that is providing a feedback path and a switch that is switching that into RX1 during TX? --> Yes. We see the output of Munin3. A small relay inside the sampler switches a feedback path to RX1. >Assuming...
- Tue Jun 22, 2021 4:58 am
- Forum: Thetis
- Topic: Orion MKII Spurs on 80 meters band
- Replies: 18
- Views: 5425
Re: Orion MKII Spurs on 80 meters band
Scott, Phil, Thank you for your comments. And sorry for getting back late to your posts due to "décalage horaire" and my morning work. As for the request of Scott, I attache the two screen shots: one is the TUNE on 3.510 900 causing spurs, the other is that of 3.511 900 without spurs. This...