I just installed this morning before reading this post but had no such issue.
Thx Richie!
Carl
NX5t

No audio in vid.
Thx
CL

Welcome back Richie!

Finally, an answer to the old question of what is causing that visually annoying spike.
Great work Scott!
Now, if we could only get Richie to write some code to eliminate it.

Thx
Carl
NX5T

Thanks for all you have done Richie.
Enjoy the rest of the good weather and cycling!
Great photo! Excellent composition.

Cheers,
Carl
NX5T

8000DLE

Hi Carl,

Those numbers sound spot on.

"They" say that you don't need to terminate the unused port, but I do, and I recommend it. It's cheap insurance (50 Ohm SMA terminators are cheap ;) )

You shouldn't see these "blow outs" associated with the feedback indicator, but you can see them if the ...

This is a bit different issue but I'm noticing my 8000DLE output power fluctuating about 4w higher from time to time while in use. After tuning up my amp with 26w drive and about 1300-1350w amp output I later noticed the amp output of 1450w. I switched the amp to standby and observed 31w output from ...

Richie....

21e running great here.
Awesome work you're doing!
Thx
Carl
NX5T

Richie...

I'm with Scott on this one.
I think your valuable time could be better spent on things more widely used.
Thanks for all your hard work.

Carl
NX5T

Richie...

Disregard my post about CPU usage. I had two instances of Thetis running, not sure how or why, but ended the task for low CPU copy running and now CPU usage is normal.

Carl
NX5T

Hi Richie, and welcome back...

I just loaded 21b and noticed something odd. CPU usage for "Thetis Only" is showing 0% to 1%. Prior usage with 2.8.11 would show 5% to 8% normally.
Great stuff you're doing and thanks very much!

Carl
NX5T

Since making the "NetworkThrottlingIndex" change to FFFFFFFF three days ago I have not had a single SEQ error during TX or RX. There is no question this change has eliminated pages of SEQ errors observed in every operating session since the Windows 10 update.
Carl
NX5T


Manufacturer: Intel ...

I made the Network Throttling Index change in Windows 10 registry and all of the SEQ errors have ended.
Thx to all,
Carl
NX5T

I had one Windows10 update on 5/1/2021 called 2004 forx64 based systems (KB4023057).
This being 5/8/2021 seems like it just started one or two days ago, but started getting another SEQ error closer to the Win10 update that is intermittent and lasts a fraction of a second causing receive audio ...

I'm not using VAC but analog audio instead. Will these registry tweaks still help?
Also, here is what I see in the registry where you said to go. As you can see in SystemProfile I see REG_DWORD, not DWORD 32. The DATA value is showing 0x0000000a (10). What should I change it to? I'm not real ...

I just started getting this SEQ error msg and is causing dropouts on transmit.
Anyone have thoughts on a reason or fix would be much appreciated.
Thx
Carl
NX5T

I should have mentioned that this data is only visible when Pure Signal is disabled.
Carl
NX5T

Can someone tell me what the Hz, dBm and MHz numbers that are constantly changing (circled in red) are referring to?
Thx
Carl
NX5T

[img][/img]

w-u-2-o wrote:Glad you got it sorted

Did you take any photos that you could post?

Scott....

FYI.... I reflowed the fan header and it's working now.
Thx,
Carl
NX5T

Scott...
Thank you for that info.
I did run the radio after installing the new fan. I had it up to 35C at one point and never heard the fan run. In the shack it can get above 25C (usually 26 to 27C) before ever transmitting. My thought was I may have over stressed the header removing the hot glue ...

Scott...

I pulled the bottom cover off and removed the noisy fan and dirty air filter. Then removed the top cover and cut the glue off the connector and removed it. The new fan came with a two pin connector which was not compatible with the three pin mount on the PA board. I cut the three pin ...

New replacement cooling fan has arrived for the 8000DLE. Can anyone that may have replaced the fan before tell me if it is done completely from the bottom of the radio? Also, is it a plug-in ( as the new fan is equipped, 2 pin) or does it require soldering?

Thx
Carl
NX5T

Thanks Scott!

Found it on Amazon...
https://www.amazon.com/gp/product/B073R ... CEDX&psc=1

Carl
NX5T

My 8000DLE fan has begun to produce a intermittent, low level howl. I suspect the bearings are becoming worn (unit is three yrs old) and should probably be replace in the near future. Does anyone have a direct replacement fan model/part number, either OEM or third party that will work?
TIA,
Carl ...

LarryW...

If you are using a Cat 5 Ethernet cable try switching to a Cat 6a cable. Cat 6a is rated for 10 gigabit speed and is shielded. I had the same issue of Thetis locking up intermittently and the Cat 6a cable fixed it. I have not had a lock-up since switching to Cat 6a five months ago.
Carl ...

Somebody needs to tell me why running VAC is better then analog audio. I have none of the issues I read about with VAC and I think my audio is fine. I have no latency issues when using RX1 and RX2 simultaneously. No additional load on my system (which is more then capable). I'm not being a smart ass ...

Richie...
2.7.0 a2 loaded and running great.
DPS/Options/ Filter size for SSB and General/ADC settings didn't carry over. Minor inconvenience.
Fyi... All previous lock-up issues appear to have been resolved with change from Cat 5 Ethernet cable to Cat 6a shielded cable.

Carl
NX5T

Here is a short video of PowerSDR displaying some strange behavior causing relay opening and closing of short duration.
Resetting the database has solved the problem. The database was reset, then an older database was imported to reload most of my settings.
https://www.youtube.com/watch?v=Zu ...