Running Protocol_2_v2.2.2 on my 7000 MKII, no issues. Many thanks Rick!

Mark

I suggest you re-start with a blank database then import a recent database. That might clear the issue (and might not, but it's worth a try).

Mark

That's great news Jim, thanks for posting.

Mark

Darren,

Can your 7000 run Protocol 2 without any problems? (asking for a friend)

Thanks,
Mark

I have a related question so I'll post it here.. My problem is that I can't turn down the blaring audio volume levels coming from the speakers when re-transmitting a captured over-the-air recording using the Quick Rec and Quick Play buttons in the Wave File Controls window. In the Wave window, after...

Ben,

What do you mean by "Anan-7000-clone"?

Thanks,
Mark

VK3ICM wrote:Thanks Mark - out of interest what mic are you running? I think I'm in a much better place now - most of my trouble appears to have been my poor mic placement.

Audio-Technica AT2035.

Mark

Thanks Scott - yes phantom power is on. Clearly a boom arm is now on my shopping list. If I shoot for ~ -3dB peaks on the MIC meter via the gain on the Motu (VAC TX gain at 0dB, TX eq off), I do see some minor clipping on the Motu display on the pops and whistles. Maybe thats ok? I'm not Scott but ...

I try to keep in mind that, generally speaking, 1) there are two sides to every story, and 2) we typically only get an earful of one side of the story.

Mark

Bryan,

Thanks for the cmASIO use notes, DeBugView says LockMode is enabled here. My clocks aren't coherent but I haven't noticed any audio glitches so maybe I'm one of the lucky ones.

Mark

Thanks Richie, I had seen that info in the cmASIO install folder, indeed that verbiage is what gave rise to my questions. I'll wait for Bryan to expound.

Thanks again,
Mark

I have several questions... 1) What is Blockmode? I've seen the term LockMode elsewhere in this forum but not Blockmode. 2) Can LockMode function even though my Motu interface isn't on the same clock as the ANAN or my computer? 3) How does one verify that LockMode is actually functioning? I ask beca...

ea3aqr wrote:I adjust PS manually on each band to avoid doubling my bandwidth requirements, but that's all.

How does one adjust PS manually?

TIA,
Mark

I suspected that would work if you tried it cuz it worked for Scott and myself.

Glad you got it working.

Mark

Jim, You never replied to my post above so I don't know if you ever tried the configuration I suggested. It's the same setup Scott advised me to try in an earlier post and it's working for me. One thing that's quirky about that setup is the ASIOdrivername in Registry is NOT set to the name of the dr...

BOOM!! I see it, thanks Bryan!

Running 2.10.3.5 pre-release 5 and I just noticed that the CM icon in the Thetis status bar is gone:


Anyone else seeing (rather, not seeing) this?

Mark

Thanks for the tip!

Mark

JJ,

My meter does show 7.6 amps during TX (at 42 watts output), but shows 0.0 during RX -- I've always just assumed that the current draw during RX was something less than 0.1 amp so the meter just registers 0.0 (but I could be wrong, as you well know!).

Mark

Jim, If it helps, here's how I've got my setup: Registry Setup.jpg VMP Setup.jpg Notice that I have the Registry pointing to "Voicemeeter Virtual ASIO", which is Voicemeeter's Channel 1. So any signal appearing on VM channel 1 output (my mic audio in this case) will get routed by cmASIO in...

W4WMT wrote:Yes it does. The lockMode will be enabled.

Thanks Bryan!

Mark

The CM-ASIO Guide speaks of a LockMode which "is entered by setting any of the highorder bits in the ASIOblocknum value". I'm not really clear on what are "highorder bits" in the ASIOblocknum value so here's a snapshot of my Registry entries: Capture.jpg Does that snapshot indica...

You're right, but 1) this thread is more than two years old and 2) the subject has wandered more than a bit over that time.

Mark

Per another thread in this forum, it's possible the factory's email address has been hacked. If that's the case then their email server may have been taken offline until the problem is resolved.

Mark

Hello again If I uninstall version 2.10.3.4 and install today's version 2.10.3.5 prerelease-4, VAC1 does not work (no audio in the headset). After doing a new installation of today's prerelease version-4 (I deleted the OpenHPSDR directory to do so), VAC1 works again. 73 Joseph Where was there any n...

If you're speaking in the context of the various performance parameters that Rob Sherwood measures and publishes, the answer is No. There are no performance improvements between the 7000DLE MKII and the G2.

Mark

Did you enable CM-ASIO in the Registry? That could be interfering with what you were doing in VAC2.

Mark

I finally got around to playing with this outstanding new feature by Bryan, W4WMT. Thank you, Bryan! :) . . For giggles I'm playing with ASIOblocknum now. The default value of 5 works fine. A value of 2 doesn't work so well. Increasing to 3 seems to be pretty good so far, but I need more time on th...

!! Success !! Scott , I finally got CM-ASIO running as hoped for, using the Registry settings you suggested and the VM settings per Ernst and Richie. Joe , I've noticed that RX1 and RX2 both utilize CM-ASIO (VAC2 has never been ASIO-capable). Also I've noticed that my laptop consumes a bit less CPU ...

Thanks for clarifying, Scott. I'll dig into my VM configuration when I get home this evening. I do recall utilizing the VM Insert feature some time ago to sidechain the mic stream thru Performer Lite so maybe there's some dangling chad somewhere in VM that needs cleaning up. I should probably start ...