Exactly the same results, rebooted PC, M-Audio M-Track set to 48000 and buffer size 64 I'm going to try the M-Audio on a different PC Hi Jim, One more thing I just remembered you should check. When you populated the registry key value with your driver name, if you left a trailing space at the end o...

I see your VAC1 is enabled.
What is it connected to?

That's correct Tony, about the sampling rate. Repeat all of yours above, but this time with the M-Audio sampling rate having been set to 48000 in advance. Looking at your debugview output suggests that you may have had the hostsample detail screen open while Thetis was trying to start. Because it's ...

K4IBC wrote:Should he change his regedit to the M-Track Solo and Duo ASIO not VM?

He did that already, as reported in the debug dump.

So I have the M-Audio M-Track Solo and have installed the software Using hostsample I get driverCount = 5 ASIO4ALL v2 M-Track Solo and Duo ASIO Voicemeeter AUX Virtual ASIO Voicemeeter Insert Virtual ASIO Voicemeeter Virtual ASIO Press any key to continue . . . Hi Jim, Was that the only output from...

Hardware is nothing special, either the on board sound card or a pair USB headphones. Where can I find the buffer setting please as I've looked in the driver and cannot see the buffer setting. Hi Jim, Are you sure that your on board sound card and/or your USB headphones have an ASIO driver? If so, ...

KC2QMA wrote:Got It
https://community.apache-labs.com/download/file.php?id=3984

That's an early version of the instructions.
See the Thetis folder after installing pre-release-4 for a pdf of the most recent version

Yes it does. The lockMode will be enabled.

If you have installed pre-release-4, the instructions for cmASIO are in the Thetis folder.

Hi Jim, Do you have DebugView from sysinternals.microsoft.com? If so, you can use it to see debug output from Thetis while it is starting which will show what went wrong with cmASIO. Otherwise, there's a couple of Voicemeeter pitfalls you can check. Voicemeeter's virtual ASIO driver buffer size shou...

If this is the case, then it would be logical to indicate information about this here in the forum header and specify another backup email! Yes, that would be the logical thing to do. Otherwise, we have absolutely no way to communicate with Apache-Labs. The last time I emailed them, I found myself ...

There's no doubt about that Mark.
It was egregiously hacked!
73

Abhi locked the 'Fraud Alert' thread against replies in the News forum, but if I were able to reply to him, I would say this: I received the aforementioned emails from a fraudster who was posing as Tony. The really bad thing is that the fraudulent email came to me as a reply to email that I had just...

I also noted my UMC status panel shows that it automatically set 64 samples under "buffer mode"; it was set to 8 with VAC so that was nice since I didn't know it needed to be set to 64. I may even break out VMP and give it a whirl again. I have been using my 7300 for digital for quite a w...

Hi Dick, I setup VAC1 and VAC2 just like yours (shown above) in version 2.10.3.5 pre-release-3 using my 7000DLE MKII. Everything works fine. I'm listening to a 40m QSO on 7.157 via RX1/VAC1 and an 80m QSO on 3.915 via RX2/VAC2. Sounds good. Not trying to rub it in. Just trying to encourage you that ...

w-u-2-o wrote:I'm attaching Bryan's cmASIO preliminary instructions here for convenience.

Standby for full instruction guide, which should clear up most questions.
Final draft is being edited and will be released soon.
73!

K1LSB wrote:One question, I haven't been able to find any Thetis mic audio level adjustment that works after I enable cmAUDIO, how are you adjusting your mic input level in Thetis?

Mark,

Use the mic slider on the main console window, just like you did before you started using VAC.

73,
Bryan

Can you confirm that if I want to use the front panel audio again I just need to remove the reg key for now ? Hi Paul, You don't have to remove the whole reg key. You can just delete the text of your asio driver name within the key value, or you can mangle the name somehow (like adding a bogus char...

Revised Timeline: We want to be transparent about the timeline moving forward. We anticipate receiving the updated pallet card within the next 8 weeks, and the upgraded heatsinks are projected to arrive within 6 weeks. With these essential components in place, we are targeting to initiate shipping ...

Roger GT wrote:As a matter of fact. I got my tracking number today!

Great, but how long ago did you order?

KC2QMA wrote:Would be great if you could select a USB audio interface ASIO driver as MIC input under Setup>General>H/W Select.

Hi OM,
Give me a PM here on the forum and I'll send you a link to a WIP that does just that.
Testing phase, if you're brave enough
73, Bryan W4WMT

I tend to force them when running data modes, especially SSTV and the like. There is nothing wrong with them afaik, but their state is not stored along the with the TX profile atm. Okay, cool. I didn't realize they weren't being stored in the TX profile. I've been working on Issue #87 with Sherman ...

ramdor wrote:VAC Audio Force In (rx1 + rx2)
VAC Audio Force Out (rx1 + rx2)

Hi Richie,
Something wrong with the resampler ratio "Force" functionality?
73,
Bryan W4WMT

Not a tick of a box.
Do that with the "Pan" sliders, i.e. slide one all the way to the left and the other to the right.
73!

ct1iqi wrote:G2 100W no display:
ordered July 3 2023,
delivered Sept. 1 2023

It's been almost one month since the last shipping update report!
Does that mean the shipments have coasted to a halt?
Or does it mean the shipments are now occurring so timely that the issue is moot?
73,
Bryan

Tony, is your G2 running Protocol-2?
73, Bryan W4WMT

Hi Tony,

What sort of audio interface are you using now on your G2?

73,
Bryan W4WMT

Take what?

Is there a protocol-2 image for the TRX DUO / Red Pitaya yet?
Bryan

Hi All,
How do we know the rumbling sound wasn't actually a signal on the band?
His panadapter is zoomed out so far, I can't squint hard enough to see if the rumble is actually within the receiver passband or not.
73,
Bryan W4WMT