I can't see any differences in the offset. Both RX offset lines/values are identical for me. RX1 and RX2 are both configured identically.

Richie thanks for rc2-b,
now consumes less CPU power even when RX2 is enabled.
Subjectively, it seems a bit more reactive to me.

Re-enabled Auto-AGC after Thetis restart (with MIDI mapped knob) still refuses to work.

I think it would be much nicer to let Richie finish the "Current Version" first. Because if new requests are constantly being built into the ongoing project, I fear that there will never be a release version. :lol: And thanks to Richie's good nature, everything is always implemented immedi...

To verify I started again with an empty MIDI profile and only mapped the RX1 and RX2 level controls to the knobs. The result is the same again.

Of course I will check rc2 as soon as it is out.

Since this behavior also occurs with a blank database, I started to examine. I've now gone the hard way and installed a clean Win10. All suggested updates were installed. Thetis installed and updated to 21k9rc1(clean Database, noting configured except radio model). So far everything works as it shou...

I need to revise my edit. https://apache-labs.com/community/viewtopic.php?f=9&t=3861&start=210#p18093. KB5010472 is not the cause. The problem is still there. Interesting is the fact that chkAutoAGCRX1 and chkAutoAGCRX2 are set to true in the database. "Auto AGC RX1" is also checke...

Today I have tested k9pre7 on a different computer and re-enabled Auto-AGC is working fine there. So I shutdown Thetis with AUTO-AGC enabled, now copied the OpenHPSDR appdata folder and OpenHPSDR Thetis folder (from the working computer) to my HAM computer to ensure all folders are equal, fired up T...

This is strange,
have k9pre7 tested again with blank database, AUTO-AGC is not re-enabled at startup.
So what can be the culprit.

ramdor wrote:
they will re-enable if you shut down with them active

Just made a test from 21k5 up to 21k7, there Auto AGC is re-enabled.
Since 21k8 it does not work, even with a blank database.

I would like to have an option to activate Auto-AGC mode every time Thetis is started, or does it already exist and i'm too blind to see.

and another one.

If you activate RX2, shouldn't VAC2 also be activated automatically? For me it did not work.

This is already the case.
Goto Setup>Transmit and mark "Highlight TX Profile Save Items" and go thru all setup pages to see which parameters will be saved in your profile.

Hello Ernst,
2Tone is there and it is working for me. You can also test ZZUT1 to activate.



If I am not mistaken, Toggle Wheel to VFOA/VFOB only applies to Behringer CMD-PL1 Midi Controller

Only a small one. ;) Just noticed that Setup>Appearance>RX Display>Grid>Alpha is not working anymore like it is in 2.8.11. Any other box/slider works fine. Compared 2.8.11 and 21k9pre6 side by side. In both versions Disable picDisplay is unchecked. Skin is IK3VIG Special. Note the grid background. S...

This was very fast. Great work as always. I like this very much.

Back then, Chris / W2PA implemented the corresponding changes in PowerSDR 3.4.4.
http://w2pa.net/SDR/2017/09/09/addition ... ancements/

No Sigi, I have not look at it yet. If you want to limit up to the edge of the spectral area, what happens if something (cat/midi/split/etc) wants to go beyond? It is not quite as simple as it seems. If it is only a mouse drag limit than that is ok and can be done easily enough. R. I will be review...

Hello Richie,
like Jörg DD8JM, I would like to ask again about the fixed band edges in CTUN mode. (TODO 24) Limit tune to viewed spectral area). I know it's not a major priority. Is there anything new in this direction?

I think, regardless of whether the step size is set via the UI or button / slider, the question should be what should be achieved with it. Depending on the type of modulation used, there are presumably other requirements, so that changes should not be so easy to implement. In addition, there is also...

I am using a Hercules DJControl MP3 LE. If "FilterBandwidth" is mapped to a wheel (this is the only option right now) it results in a 33Hz step in PowerSDR and Thetis as well. Wheels mapped to Filter High / Low results in 50Hz step. It apparently depends on the controller used, how large o...

I'll have a look tomorrow.
Do you use PowerSDR or Thetis?

I am not exactly sure what you mean.
Please send a screenshot or the CAT command in question.

Which MIDI controller are you using?

Thanks Scott.
Just noticed the pics are very big.

Hello Paul, Unfortunately, the VFO wheels cannot be pulled off from above. To dismantle the large wheels, you need to remove all screws from the back, then carefully separate the case halves from each other. Now you can see the back of the PCB. There you will see a so-called C-clip. Remove this C-cl...

Thanks Scott for answering. I thought I would just give it a try. I've always wanted to test linHPSDR. Since I don't have a dedicated Linux computer, that would have been a possibility. And just to test this, I didn't want to set up a dual boot system. It was the play instinct that came over me once...

Hello, I'm trying to start linHPSDR in WSL, but no HPSDR device is found. I suspect it is due to the network configuration. In WSL, for eth0 172.30.253.10 255.255.240.0 is used. Since the real network is in 192.168.178.x area, the real SDR address is 192.168.178.43. Internet under Linux is not a pro...

For me it works without problems.

Big arrow changes VFO



Small arrow changes Filter

I want to note that the website certificate is invalid / expired. Chrome complains about an invalid certificate. This happens on all my computers, tablets, mobile phones. This server couldn't prove that it is apache-labs.com. His security certificate has expired in the last 24 hours. Possible reason...

I have just installed both versions 32 + 64 bit on my HP Elitebook I5 8365U @3,9 GHz, 4GB RAM. It runs on Win11 and has never seen a Thetis installation before. I could hardly see any difference in the CPU load. With the settings you specified RX1 768000 SR and RX2 384000 SR; both RX on, the load is...

Can someone explain the differences between Anan100E and 100D?
I searched the net on 100E, but received only a few / useless information.

Pls check your skin folder if chk2TONE-0.png and chk2TONE-1.png are present.

Just a visual extension. Some more characters can be displayed so the names of the transmit profiles are better readable. Beside the dark background I also tend to have a darker frame for all dropdown boxes also. But I dont know how to color the frame in Visual Studio. As alway I have no clue what I...