Page 1 of 1
VAC Tutorial
Posted: Sun Dec 10, 2017 12:28 pm
by w-u-2-o
Re: VAC Tutorial
Posted: Sat Nov 10, 2018 4:59 am
by Dick
Hi Scott
Your tutorial discusses ===>
"2.0 This document is divided into the following parts.
A review of the functional basics, rules and software limitations associated with the PowerSDR virtual audio interface.
Suggestions for testing and tuning system performance for real-time audio.
How to quickly setup a USB headset for use with PowerSDR.
Virtual PTT switching for virtual audio.
Latency: what it is and how to minimize it.
How to setup up Voicemeeter Banana and interface digital mode software audio streams.
Virtualizing CW operations.
Integrating Digital Audio Workstation (DAW) software.
"
but I do not see anything about how one can plug a microphone into the computer running PowerSDR and
pipe the audio to a remote ANAN-200D/7000dle/etc using VAC1.
Is this possible ? My radio room in the shop gets down in the low 30's quite often in Winter and operating there gets
pretty uncomfortable!
Re: VAC Tutorial
Posted: Sat Nov 10, 2018 12:31 pm
by w-u-2-o
Dick,
Yes, using VMB to route microphone and receiver audio was not covered in the tutorial, which is pretty basic. My radios live in a rack in the basement and I operate exclusively from my second floor studio office, i.e. I do exactly what you are seeking to. I will address your questions in your other thread--look there soon.
73,
Scott
Re: VAC Tutorial
Posted: Sat Nov 10, 2018 4:16 pm
by Dick
GM Scott
Many thanks for addressing this topic. It seems like every time I try something related to software applications changes
it ends up being a "tar-baby" where the problem just gets worse! Then I spend days getting something that worked
fine back in operation.
RF and circuit design is a comfortable arena for me but this computer stuff seems like fighting in a Vietnam jungle
I will look at what your next posting provides. Again many thanks for your SW-knowledge and dedication to growing
the SDR spirit in our Ham community.
73 Dick/w7wkr
Re: VAC Tutorial
Posted: Thu Nov 14, 2019 10:25 am
by Tony EI7BMB
I thought this facebook post by voicemeeter might be a useful reference.
"Let's remind the Voicemeeter internal audio routing diagram to explain how this is logical! Like for any hardware mixers you can get this map in mind: Audio comes from the top, then goes to the right by the BUS assignation buttons and finally goes down to audio outputs"
- voicemmeeter.jpg (122.79 KiB) Viewed 33806 times
Re: VAC Tutorial
Posted: Fri Nov 15, 2019 3:40 pm
by Dick
Tony -- Tony EI7BMB -- Many thanks for the detailed picture of Voicemeeter's signal routing.
VM and my computer have been playing well for me for quite a while now BUT sometimes I
have to resort to my detailed notes for all the settings in the WSPR/VM/Soundcard
configuration when everything quits working together.
73 and THANKS to everyone who turn on the 'light' in dark situations.
73 Dick/w7wkr
Re: VAC Tutorial
Posted: Fri Nov 15, 2019 5:45 pm
by Tony EI7BMB
Glad I could help Dick
Re: VAC Tutorial
Posted: Sat Mar 27, 2021 1:56 pm
by Tony EI7BMB
I've just installed voicemeeter potato 64 bit version and it seems to be working well so far.
Re: VAC Tutorial
Posted: Sat Mar 26, 2022 5:50 am
by VE6IV
Scott,
did the tutorial get moved? This link is not working for me.
Re: VAC Tutorial
Posted: Sat Mar 26, 2022 11:17 am
by w-u-2-o
My apologies, my website is down, the server had a major hardware failure, spare parts will not arrive until Monday.
Re: VAC Tutorial
Posted: Mon Mar 28, 2022 1:10 pm
by ON7WP
My Thetis audio was fine since I was running voicemeeter as you suggested.
Recently it stopped working and I have no idea any more what went wrong. No more audio via ASIO... Did not change a thing. No more audio to or from Voicemeeter from Thetis. Can hear my own audio in voicemeeter.
classic VAC works OK.
Any tips? W10 updates related maybe ???
Re: VAC Tutorial
Posted: Mon Mar 28, 2022 1:17 pm
by w-u-2-o
@ON7WP
Start a new topic in the Digital (Virtual) Audio sub-forum, please, and we'll sort it out there rather than clog up the tutorial topic.
Re: VAC Tutorial
Posted: Sun Jun 18, 2023 10:52 pm
by Torrey
Scott,
I spent the afternoon working my way through setting up VAC audio through the PC using Voicemeeter/Banana.
'Love the quality of the sound through my high-end studio monitors.
Now, I am ready to set up microphone transmit using VAC. I have read your summaries and and those of W1AEX.
My goal is to use the EV RE-27 N/S microphone currently plugged into the front of my 7000DLE MK III. Nothing I have read tells me how to use a good dynamic microphone and transmit through a VAC. I am guessing that one way to do this is to run the RE-27 to the XLR jack on the back of an external sound card and from there to the line-in jack. Is there a way to instead utilize the PC's sound card? Is there a tutorial on this subject available? Thank you!
73 Torrey N9PY
Re: VAC Tutorial
Posted: Sun Jun 18, 2023 11:50 pm
by w-u-2-o
You are correct, you need an appropriate sound interface. Most folks use a pro style USB type. There's no tutorial per se, but this topic might get you going down the right road:
viewtopic.php?f=13&t=4546Start a new topic on this in the digital audio sub-forum of you need to.