Thetis v2.10.3.4 Released

Locked
User avatar
ramdor
Posts: 1582
Joined: Wed Jul 03, 2019 3:07 pm
Contact:

Thetis v2.10.3.4 Released

Post by ramdor »

Final version of v2.10.3.4 has been released

Thanks to all that tested the 6 rounds of pre-release for this version.

Get it here : https://github.com/ramdor/Thetis/releases

!! CW Warning !!

If you use CW and you have different RX and TX antenna ports configured, there is a high potential for full RF power to be present briefly on the RX port. This may lead to damage of any sensitive equipment attached to the RX port such as active antennas and the like. This situation can occur if you utilise the CWX form, serial keying/PTT, and standard hardware keys plugged into the radio. This issue is currently under investigation and has existed in Thetis for an extended period (years and years). If you are interested in following the progress, you can read more about it on GitHub here : https://github.com/ramdor/Thetis/issues/228

**Note: You can revisit these release notes by clicking the button in the setup form within the General -> H/W Select tab.**

Please report any issues over on github here : https://github.com/ramdor/Thetis/issues/new/choose

v2.10.3.4 Change Log
[add] show on startup options for ampview and linearity/ps window. Set in the linearity/ps window
[add] can now ignore 14bit Midi messages. More devices should work. Option in Setup->Serial/Network/Midi CAT->Midi
[add] can now combine midi control id, channel and status to be used as the control ID. This should allow devices that share controlIDs for multiple buttons/sliders to work. Options in Setup->Serial/Network/Midi CAT->Midi
[add] certain skins might make it snow !
[add] option to prevent rx1+rx2 attenuator linking when using diversity. Setting in the diversity form
[fix] you can now hear rx2 audio when tx'ing on rx1 and setup->rx2->auto mute rx2 on tx is turned off
[fix] mic phase reverse now calling correct function in WDSP, and can be turned on/off
[fix] Hercules DJControl Starlight midi device is now better handled. Wheel finger press for example are ignored. If you used this device before you will need to reconfigure as the control IDs will have changed
[fix] PortAudio #850 fix included
[fix] FM should now use low/high cuts. Carlson's rules used for filter width display in FM rx and tx
[fix] Andromeda ModeSpecificForm shouldn't now clear on console resize
[fix] scope in TX should now work
[fix] spot sun/greyline track should not forget the skin background if track is turned off
[fix] ui controls on the multimeter containers should now not get stuck visible
[fix] attenuator controls should now not appear above meter containers when coming out of tx
[change] tweaks to waterfall agc to minimise screen wide pulse on T/R
[change] spectrum+waterfall low/high step sizes lowered to 5
[change] multimeter container no title bar. Now applies even if not pinned. Hold shift and move mouse in the title bar area to bring it up even if hidden
[change] removed old noise floor calc method + option from setup form
[change] removed old http server as was non operational
[change] cosmetic and layout improvements to setup by Sigi DH1KLM
Last edited by ramdor on Sun Nov 19, 2023 9:03 pm, edited 1 time in total.
User avatar
oe3ide
Posts: 423
Joined: Tue May 05, 2020 8:36 am
Location: JN78XK
Contact:

Re: Thetis v2.10.3.4 Released

Post by oe3ide »

Thans Richie! As always, fantastic job!

73 Ernst
User avatar
ginger
Posts: 6
Joined: Thu May 06, 2021 9:19 pm
Location: UK

Re: Thetis v2.10.3.4 Released

Post by ginger »

thanks Richie
User avatar
Tony EI7BMB
Posts: 680
Joined: Sun Apr 09, 2017 2:31 pm
Location: Dublin
Contact:

Re: Thetis v2.10.3.4 Released

Post by Tony EI7BMB »

Thanks Richie
User avatar
ramdor
Posts: 1582
Joined: Wed Jul 03, 2019 3:07 pm
Contact:

Re: Thetis v2.10.3.4 Released

Post by ramdor »

A quick video covering most of the changes in 2.10.3.4



73
User avatar
KA5KKT
Posts: 157
Joined: Thu Aug 06, 2020 6:51 pm

Re: Thetis v2.10.3.4 Released

Post by KA5KKT »

Shall we assume that we are to uninstall the prior version prior to installing Thetis v2.10.3.4?


Kind regards,
Dick - KA5KKT
User avatar
ramdor
Posts: 1582
Joined: Wed Jul 03, 2019 3:07 pm
Contact:

Re: Thetis v2.10.3.4 Released

Post by ramdor »

Sigi, DH1KLM, has set up his big collection of skins so that everyone can get them through the skin server. 8-)
skin1.png
skin1.png (244.37 KiB) Viewed 38567 times
User avatar
oe3ide
Posts: 423
Joined: Tue May 05, 2020 8:36 am
Location: JN78XK
Contact:

Re: Thetis v2.10.3.4 Released

Post by oe3ide »

A lot of great skins! Thank you Sigi!

73 Ernst
User avatar
n2gq
Posts: 148
Joined: Sun Dec 18, 2022 7:26 pm

Re: Thetis v2.10.3.4 Released

Post by n2gq »

Okay cool going to try the midi controllers I have here.

Jay n2gq
Jay N2GQ
Trucker
Posts: 444
Joined: Wed Nov 03, 2021 5:16 pm

Re: Thetis v2.10.3.4 Released

Post by Trucker »

Nice update.
It's snowing in 8000DLE/Thetis land!
20231120_192017.jpg
20231120_192017.jpg (4.84 MiB) Viewed 38433 times
User avatar
KA5KKT
Posts: 157
Joined: Thu Aug 06, 2020 6:51 pm

Re: Thetis v2.10.3.4 Released

Post by KA5KKT »

For me, the waterfall colors have gone wonky with v2.10.3.4
User avatar
ramdor
Posts: 1582
Joined: Wed Jul 03, 2019 3:07 pm
Contact:

Re: Thetis v2.10.3.4 Released

Post by ramdor »

KA5KKT wrote:For me, the waterfall colors have gone wonky with v2.10.3.4
Use github to report the issue. Provide images, the palette you are using, screen shots of the waterfall display-rx1/2/tx sections. Show what you obtained with an old version, compared to what you get now. I am not a mind reader so need some actual workable info other than 'wonky'.

Note: I fixed a reversed RGB value issue in 2.10.3.4 for linlog/lingrad/linauto which has actually turned them into a mess, but will be resolved in next release.
User avatar
KA5KKT
Posts: 157
Joined: Thu Aug 06, 2020 6:51 pm

Re: Thetis v2.10.3.4 Released

Post by KA5KKT »

I suspect

"Note: I fixed a reversed RGB value issue in 2.10.3.4 for linlog/lingrad/linauto which has actually turned them into a mess, but will be resolved in next release."

Explains what I have been seeing.


Dick - KA5KKT
ki4tga
Posts: 29
Joined: Sun Jan 19, 2020 5:03 am

Re: Thetis v2.10.3.4 Released

Post by ki4tga »

I just did this software update. Do i need to update my G2?
Trucker
Posts: 444
Joined: Wed Nov 03, 2021 5:16 pm

Re: Thetis v2.10.3.4 Released

Post by Trucker »

ki4tga wrote:I just did this software update. Do i need to update my G2?
Since Thetis only runs on your pc, there shouldn't be any problems connecting to your G2.
James
WD5GWY
ki4tga
Posts: 29
Joined: Sun Jan 19, 2020 5:03 am

Re: Thetis v2.10.3.4 Released

Post by ki4tga »

Trucker wrote:
ki4tga wrote:I just did this software update. Do i need to update my G2?
Since Thetis only runs on your pc, there shouldn't be any problems connecting to your G2.
James
WD5GWY

yes sir, it connected with no issues. ty
ki4tga
Posts: 29
Joined: Sun Jan 19, 2020 5:03 am

Re: Thetis v2.10.3.4 Released

Post by ki4tga »

Trucker wrote:Nice update.
It's snowing in 8000DLE/Thetis land!
20231120_192017.jpg

how did you make your s-meter smaller to go between the nB buttons and the others
User avatar
oe3ide
Posts: 423
Joined: Tue May 05, 2020 8:36 am
Location: JN78XK
Contact:

Re: Thetis v2.10.3.4 Released

Post by oe3ide »

ki4tga wrote:
Trucker wrote:Nice update.
It's snowing in 8000DLE/Thetis land!
20231120_192017.jpg

how did you make your s-meter smaller to go between the nB buttons and the others
You can resize every meter container by dragging the right bottom edge of the container (a double arrow will apear)
ki4tga
Posts: 29
Joined: Sun Jan 19, 2020 5:03 am

Re: Thetis v2.10.3.4 Released

Post by ki4tga »

oe3ide wrote:
ki4tga wrote:
Trucker wrote:Nice update.
It's snowing in 8000DLE/Thetis land!
20231120_192017.jpg

how did you make your s-meter smaller to go between the nB buttons and the others
You can resize every meter container by dragging the right bottom edge of the container (a double arrow will apear)
ty i feel stupid now
va7qi
Posts: 135
Joined: Mon Apr 10, 2017 4:22 am
Location: Quadra Island, BC
Contact:

Re: Thetis v2.10.3.4 Released

Post by va7qi »

Just noticed that the Lock function does not work in 2.10.3.4. The LED next to the Lock button on the Andromeda lights up, but I can still change the frequency using the encoder.

73 de va7qi, ....Erik.
User avatar
Tony EI7BMB
Posts: 680
Joined: Sun Apr 09, 2017 2:31 pm
Location: Dublin
Contact:

Re: Thetis v2.10.3.4 Released

Post by Tony EI7BMB »

Anyone notice that NB stays on during TX ?
SA3ATF
Posts: 103
Joined: Mon Apr 10, 2017 9:42 pm
Location: Vasterasen, Bispgarden, Sweden JP82HX
Contact:

Re: Thetis v2.10.3.4 Released

Post by SA3ATF »

Tony EI7BMB wrote:Anyone notice that NB stays on during TX ?
Not here anyway Tony.
I don’t suffer from insanity, I enjoy every second of it!
User avatar
Tony EI7BMB
Posts: 680
Joined: Sun Apr 09, 2017 2:31 pm
Location: Dublin
Contact:

Re: Thetis v2.10.3.4 Released

Post by Tony EI7BMB »

SA3ATF wrote:
Tony EI7BMB wrote:Anyone notice that NB stays on during TX ?
Not here anyway Tony.
Sorry I should have posted ion 10.3.5 thread
User avatar
w-u-2-o
Posts: 5941
Joined: Fri Mar 10, 2017 1:47 pm

Re: Thetis v2.10.3.4 Released

Post by w-u-2-o »

Locking this topic, please continue on in the 2.10.3.5 topic!
Locked

Return to “Thetis”