PTT for K9DUR VoiceKeyer software

radiotx
Posts: 29
Joined: Sat May 06, 2023 9:47 pm

PTT for K9DUR VoiceKeyer software

Postby radiotx » Thu Jul 11, 2024 10:52 pm

I recently configured K9DUR's VoiceKeyer with Thetis v2.10.3.5.

In order to control PTT for VoiceKeyer, the manual states the following:
VoiceKeyer controls the radio PTT by toggling the DTR and/or RTS pins on a PC serial port.
Most commercially-available sound card interfaces sold for digital mode operation support this
method of PTT control. PowerSDR supports this method using a virtual serial port created with
VSPmgr, com0com, or similar program. SmartSDR supports this method by creating a PTT
serial port in SmartSDR CAT.
VoiceKeyer also allows up to two messages in each profile to be triggered by pulsing one of the
modem control lines (CTS, DSR) on either the serial port used for PTT control or on another
serial port.
I ended up using Eterlogic VSPE (demo mode at the moment) and it works. Just curious if there is another 'baked in' way to accomplish this type of PTT control within Thetis. Thanks for any input!
User avatar
w-u-2-o
Posts: 5924
Joined: Fri Mar 10, 2017 1:47 pm

Re: PTT for K9DUR VoiceKeyer software

Postby w-u-2-o » Fri Jul 12, 2024 3:28 am

No other way to accomplish serial port PTT other than the one setting provided to assign a serial port and signaling line in Thetis setup.

Thetis does also support CAT PTT if the other app can utilize that method.
w3ub
Posts: 111
Joined: Fri Dec 14, 2018 6:32 pm
Location: Lunenburg, NS/Florida

Re: PTT for K9DUR VoiceKeyer software

Postby w3ub » Fri Jul 12, 2024 11:29 am

I use the K9DUR keyer sometimes, as you found out the only way to get PTT is to set a serial port in K9DUR and since this is a "virtual" port, make a pair in VSPE and use paired port in Thetis.

VSPE is worth the one time cost I think.

Doug
radiotx
Posts: 29
Joined: Sat May 06, 2023 9:47 pm

Re: PTT for K9DUR VoiceKeyer software

Postby radiotx » Fri Jul 12, 2024 12:29 pm

w3ub wrote:I use the K9DUR keyer sometimes, as you found out the only way to get PTT is to set a serial port in K9DUR and since this is a "virtual" port, make a pair in VSPE and use paired port in Thetis.

VSPE is worth the one time cost I think.

Doug
Thanks Doug! I just wanted to make sure I was not overlooking something in Thetis. I will go ahead and purchase the license.

73s

Clif
K1LSB
Posts: 706
Joined: Wed Feb 05, 2020 5:25 pm

Re: PTT for K9DUR VoiceKeyer software

Postby K1LSB » Fri Jul 12, 2024 12:33 pm

VSPManager is free, I've been using it for years, it's been reliable like a belt buckle (at least for me).

Mark
radiotx
Posts: 29
Joined: Sat May 06, 2023 9:47 pm

Re: PTT for K9DUR VoiceKeyer software

Postby radiotx » Fri Jul 12, 2024 12:42 pm

K1LSB wrote:VSPManager is free, I've been using it for years, it's been reliable like a belt buckle (at least for me).

Mark
Thanks! I will check it out.
User avatar
w-u-2-o
Posts: 5924
Joined: Fri Mar 10, 2017 1:47 pm

Re: PTT for K9DUR VoiceKeyer software

Postby w-u-2-o » Fri Jul 12, 2024 2:18 pm

I've experienced a lot of problems with VSPM. I'm a fan of VSPE. YMMV.

Return to “Thetis”