Laurence,

It happened now twice, always in the morning when booting and after having installed openvpn the day before. According to the installation instructions, the system will be updated daily (I assume a command like sudo apt-get update and sudo apt-get upgrade will be performed daily) if not ...

Hi Michael,
Whilst I cannot comment on this issue, I can tell you that a service like Tailscale is very easy to configure and allows simple access to many systems securely. It uses Wireguard protocol.
I can highly recommend it!


Regards
Mike

I’ve been setting up remote connection to my pc with thetis and mumble, but only really just thought about power on.
Can’t believe there isn’t a standard way to do this remotely that does not require jumping through these hoops!

No sorry, worked for me. Are you sure you loaded the v17.bin file? Also full shutdown?
Ahh, no, I followed the instrucitons at the start of this thread.

click open file
navigate to the file ~/github/Saturn/FPGA
select file saturnprimary.bin
makes sure the Primary radio button is selected
click ...

In VNC open terminal en run the commands, that should work.
Ok, done that, still seems to show version 10 though?
Screenshot 2024-11-01 at 17.29.48.jpg


Here is the original before I updated
Screenshot 2024-11-01 at 16.20.43.jpg

I did the flashwriter and chose the correct file, shutdown etc ...

PH7R wrote:

g6phf wrote:So I need a display to do the flash it seems? Or is there some switch to run from terminal?
Thaanks
Mike

Did you check this thread and instructions?
viewtopic.php?f=48&t=4772

Thanks yes. I am logged in via ssh. I will connect vnc

So I need a display to do the flash it seems? Or is there some switch to run from terminal?
Thaanks
Mike

Hi,
This may be a daft question, I just got a G2 last week. How do I see the current firmware version I am running?
Is this the correct place? If so mine shows 2.0.0 which seems very different to version 17 mentioned here?
Thanks
Mike
Screenshot 2024-10-30 at 10.13.19.jpg
Hi Mike,

just start the ...

I2NOY wrote:For weak signals you have to set properly T1 and T2 thresholds. With default values in SSB the voice is cut.

Thanks. So is it a case of listening to a signal whilst adjusting? Or do you have any figures I can start with for G2 ?
Thanks!

Hi,
This may be a daft question, I just got a G2 last week. How do I see the current firmware version I am running?
Is this the correct place? If so mine shows 2.0.0 which seems very different to version 17 mentioned here?
Thanks
Mike

There is nothing wrong with those settings. However, the "trained" mode of NR2, new in this latest version, is far superior to the Gamma mode. Nevertheless, the Gamma mode should be easily noticeable when NR2 is enabled.

You do have NR2 enabled on the main UI, right? ;)
Thanks, yes :) Well I ...

Hello. Interesting. I bought 2 yamaha Studio monitors for about 4 days ago and has about the same as you but focusrite 4 Gen. I also discover pops
but only in 1 monitor. c
Change it to another place longer away from everything else but same monitor pops. Now I am on my sunsdr2 dx to the same ...

Hi
NR2 seems to have stopped working. I have a feeling I may
have changed one of these settings.
Can somebody please share there’ settings or point out which
setting should be adjusted.
Thanks

Hi,
I am very pleased with my G2 but noticed I am getting little pops on the receive audio.
I don't recall getting this with my HL2 but I may be wrong and now I am being more critical.
I onlly get these when using my external USB audio device. I have XLR mic and monitor speakers plugged in to this ...

Hi
Can the G2 make use of pure signal without an external sampler?
Yes. Also, just for completeness, you can use it this way with an external amp but it will only linearize the internal amplifier in that case.


If so, how is this enabled in Thetis?
It is the default configuration. The settings ...

Hi
Can the G2 make use of pure signal without an external sampler?
That is, does it have an inbuilt sampler at the output stage?
If so, how is this enabled in Thetis?
Thanks
Mike

gw0gei wrote:£2700 ono

Hi,
is your 7000dle mk2 still available?
Thanks
Mike

Thanks for the replies.

Looking at the old thread/diagram that wu20 suggested there may be no real advantage to using the TRS mic socket on the back of the G2?
I could continue using the Audient ID4 audio interface and take this input to Thetis?
Or am i missing somehting.
73
Mike My ...

Thanks Svante, I may just use this as I also have 2 monitor speakers connected to the Audient ID4
73
Mike

Thanks for the replies.

Looking at the old thread/diagram that wu20 suggested there may be no real advantage to using the TRS mic socket on the back of the G2?
I could continue using the Audient ID4 audio interface and take this input to Thetis?
Or am i missing somehting.
73
Mike

Ahh, thank you. My bad. I do have a cloudlifter I use with it now as the Audient ID4 does not have enough gain. However I think I read the XLR input has some extra gain? So perhaps it will work.

So my next question, how does the microphone path get from XLR to Thetis on my PC ? Can I select the mic ...

Hi,
I am a prospective G2 owner. I have a Sure SM7B which is a good XLR mic but requires 48vdc phantom power.
I assume there is no way I can use this in the G2 XLR port?

Also, what is the advantage of using this port over say the current way that I use it, via an external USB sound card/ Audient ...