How I setup My G2 for remote.

How I worked around power on/off of the G2
Thanks to a post on either groups IO or the community to look at J9 on the PI module.
There are two wires among many that are wired to the front panel pushbutton.
Colors are black and blue in my radio that go to J9 See ...

Yep they anounced it at dayton may of 2024 but in typical Flex fashion it wasn't available to the public until a little over a year later in June of 2025.
The nail in the coffin was that the adaptive pre distortion software update (June of 2025) for the 8000 series would only work with the radio and ...

The Fan you listed above Noctua NF-A12X25 PWM is the wrong voltage. It should be 5V with CFM of 52 also the 4 pin connector will need to be modified as there a two strips of plastic meant to fit in a specific 4 pin connector. If used you will need to trim down those two strips to enable it to fit ...

Ernst
That was it.
Disable PTT was on. I looked at many settings but missed that one.
Appreciate the help.

Bob KC9RF

I have received a new G2. Everything works fine except the following:
PTT works fine in PIHPSDR and SDR Console. However PTT does not work in Thetis. Mox will key up transmitter but PTT does not. Are there any settings that I might be missing in Thetis.

In General settings I have PTT enabled. See ...

Joe
The Radio Was held in New Delhi for 3 days then on to Ontario and just Arrived in Memphis, TN at 11:02 PM 4-26-24 which is a FedEx Hub. It will be interesting to see where it goes next. It will be a world traveler for sure. I wonder if I can get frequent flyer miles?

Bob

Shipping update as I ordered a G2 without display on Feb 12 and did the 1k prepay. On April 14th I received invoice for the rest and paid via PayPal. I was told via email that it had to clear customs and on 4/23 I received a notice that Shipping Label was created. As of the 24th because of time ...

Note:
Others are having the same issue as I have a post on groups IO as well. Remotely I can click Mox on my local computer through
remote desktop and observe the same issue. Also I can mute my usb mic which I'm using remotely and see a spike using RCFORB from
remote hams eliminating any background ...

Bryan
Have already setup downward expander. However I tried playing around with settings but there is no improvement on what I already have
setup.

Bob KC9RF

FYI
I have put in a delay of 450ms which temporary works around the problem. However this amount of delay is a problem
with a normal conversation if I don't pause it will more than likely cut off the first part of a sentence or call sign.

Looks as though there should be software solution to this ...

EDWIN & all who have replied

Thanks for the input

I reduced Master AF and RX1 AF and no spike was observed. I'm operating remote so won't be able to do any hardware changes. Using virtual audio cables.

So how can I block the RX audio from causing this problem with a setting or software?

Bob ...

Gary also put a post on ANAN Groups I/O which shows a better video of the spike.
I just tested again and it appears that when I have NR on it goes away. NR off or NR2
I tested both remote using RCFORB PTT from remote hams software and also just selecting MOX I get the same results.
the spike ...

Gary
Current using protocol 1 because of sequence errors. I will be doing a firmware update when I get back to QTH in April as I'm
running remote from South Texas.
The settings were similar to what you displayed on options menu.
I tried what you had but neither works.
Bob

Hi All
First running Protocol 1 and ANAN 7000 DKE III firmware 2.8 Thetis version 2.10.3.5 x 64. I'm getting a momentary spike just after pressing mox or ptt running remote on transmit. Thoughts/settings?

Bob KC9RF

Looking for the above in USA. Let me know what you have to sell. Must have 2 ADC's for independent receivers.

Thanks for looking
Bob