Richie is right and his typo, not leaving the space is now worth millions $$ to prove that his code was lifted and used and Olliter lied about it.
Everything is okay till someone lie about it. They should admit and be sorry about it and if possible taken to court. Bill should be shared with us all ...

Thankfully, RF is visually blind. Some of best performing devices I've measured are aesthetic nightmares (and vice versa).

I've no idea about the KM3KM sampler but it's likely a local project from Miami. My understanding is the Lux and Mercury III amps are designed by RZ1ZR (not just the LCD ...

I downloaded The latest final release from GitHub and the new flash screen of Thetis looks amazing.
I wonder if the announcement is not here in this forum, or if if there is something wrong with me as I am unable to see it.

73
Bhanu
VU2MB

What I am talking about a final release and not a ...

What I am talking about a final release and not a release candidate. I am using it and its not a RC.

73
Bhanu

I downloaded The latest final release from GitHub and the new flash screen of Thetis looks amazing.
I wonder if the announcement is not here in this forum, or if if there is something wrong with me as I am unable to see it.

73
Bhanu
VU2MB

Dear Bernhard DL1OF

Thanks for your reply. Now I realise that 100d and other models like 100 and 10 may require manual jumper settings on the radio card. That's why its not here because it is not software selectable.

73

Bhanu
VU2MB

Hello

Just curious in Thetis setup (General> HW Setup why the Hardware options area remains Blank where in 200D and later it's available and you
can choose MIC Bias and PTT.
Please suggest
Thank you
73

Thanks Richie
So many new features if compare with a version thats just a couple of years old version. Completely revamped i must say.

Please let me know if after using RX2 when you switch it off to work only with RX1, if it possible that thetis goes back to the window size it was setup prior to ...

I found out the answer when I researched the forum so now I know how and why of the mystery.
Thanks, Scott.

73
Bhanu
VU2MB

Hello,

I'm interested in understanding what the S meter should read on a dummy load or when the radio is on without an antenna connected.

I recently installed 12mm and 9mm Fair Rite snap-on ferrites on everything, along with an EMI AC line filter, which has significantly reduced noise. However, I ...

Dear Richie,

Thanks for your continuous support and I have added the line to the host file.
the website was pinging and I restarted and ran Thetis & reached the skin server tab and was
disappointed by strange behaviour.

Earlier first thing I used to see Obtaining skin server list but this time ...

Dear Richie,

Without shutting Thetis would not let you try again as the msg on the screen won't go away and restarting the thetis only way to get the skin server retry to fetch the details and I did that several times without luck. Tried flushdns after your suggestion and no luck either.
Restarting ...

Dear Richie,

I have added Google Public DNS 8.8.8.8 to my network connection and now the link you provided can be opened without any issue when I click on it. Thetis is still not fetching the 4 server list.

Any clue now?
73
Bhanu
VU2MB

Dear Richie,

Thank you. Will investigate tomorrow and try to get in touch with the ISP.

Appreciate your help.
73

Bhanu
VU2MB

Dear Richie,
Thanks for your quick response.
Not clear what you meant check "https://raw.githubusercontent.com/ramdo ... rvers.json"

when I click the link I get an error message
This site can’t be reached
raw.githubusercontent.com took too long to respond.

I can see the skin server raw file ...

Hello,

I am running Thetis V2.10.3.4 X64 and cannot access the skin server on my desktop and laptop.
When I go to setup and skin servers after the initial msg "Obtaining skin server list from GitHub" it waits 30-45 seconds and I get the "Unable to retrieve skin server list" msg.
Here are the ...

Dear Chris W2PA, Ernst OE3IDE & Hans PA0Q

I am back and I have changed power-saving properties and now the FT8 does not
stop transmitting. Earlier only PTT used to work and no power after 15/20 minutes of inactivity.
I have tested up to 1 hour inactivity and it transmits normally. (Thetis used to ...

Dear Hans PA0Q,

Thank you doctor for the suggestion for this medicine. I am travelling and will be back by Friday and after testing Power saving options
this medicine will be administered for sure. This has been going on for a very long time and Thetis has seen several updates but this issue ...

Dear Chris W2PA & Ernst OE3IDE,

Thank you very much for your responses and diagnostics. I am sorry for not responding promptly.
I was away. Yes restarting WSJT-X and JTDX corrects the issue. PTT always keeps working but its
TX audio that stops.

Just tried to play with power saving settings and ...

Hello,

I have noticed for a long time that when I am using FT8 using WSJT-X or JTDX and don't transmit for 15/20 minutes or so and then call someone,
Thetis goes into transmit mode but no power output and the only solution for me till now was to shut the JTDX or WSJT-X and
re-start it to function ...

Dear Richie,

Thank you.

All issues resolved.

Thank you for your time and efforts in resolving the issue.

73
Bhanu
VU2MB

Thank you, Richie,
I will doing that in a few minutes

73
Bhanu

Dear Richie,

Thank you for the pre-release.
Here situation remains the same and my PC still do not register the changes
despite asking to save and overwrite the TX profile.
and new changes are not stored.

I know it should not happen as others have reported that their issue is now resolved.
if you ...

Hello friends,

My Mercury IIIS HF amplifier is working just fine and mine was made from bare PCBs. I enjoyed building it despite having no experience handling SMD components and the smallest footprint was 0805. Now I have decided to go ahead and start another project which Kurt Moraw designed and ...

This picture popped up on Facebook just now as memory of the day. This picture was taken with Rob Sherwood NC0B when he visited our stall. This was first time Apache Lab visited Dayton and Anan 200d was announced and the Orian card was demonstrated there along with anan 10 and 100d displayed.
Thank ...

Here it is

https://apache-labs.com/download_file.p ... ds_id=1020

73
Bhanu
VU2MB

More important is to find out if the boatloader code (.pof file )
Location is confusing or not? Otherwise I will cause issues for someone requiring it in the future.

If the radio is dead for the moment, you may call it bricked or by any name should not matter till the final obituary is written. In ...

So what do you think bricked it?

I really don't know.
This is the second time during the last couple of years.
Bootloader worked properly.
It erased the earlier firmware and then programmed the P1 Metis_Orion_MkII_v2.7_K5SO_5-4.rbf
after the power cycle and moved the jumper switch to off There ...

Yes Indeed, bootloader programme numerous times on 8000/200d and 100d for updating firmware
and also for setting up static ip.

It was not a typo. Even I thought thst bootloader was good as heartbeat was normal in bootloader mode. I tried uploading.rbf files P1 & P2 and bootloader program shows that it was progrmmed properly and after power cycle it wouldn't work as there was no heartbeat in normal mode. So I was advised by ...